硬盘读盘失败，通常表现为开机时显示"failed to read disk"。解决此问题，首先应检查硬盘的数据线和电源线是否接触良好。若问题依旧，尝试进入BIOS，检查硬盘是否处于正常状态。确认BIOS中第一启动设备设置正确，避免将非启动设备设为优先启动。若以硬盘作为启动盘，检查设置是否正确。如果并非以硬盘为启动盘...
电脑一直显示faild to read disk 1.检查显示器和主机线、接头是否接通;2.如果外接显示器看到系统已经正常启动,那么可以检查键盘上方用于显示屏合上时关闭供电的开关按键是否正常;3.如果外接显示器和弹出显示屏断电开关都没问题的前提下,显示器不能显示,那么可能是系统
由于a disk read error occurred的中文意思是一个硬盘的读取错误，基本上可以判断是由于硬盘故障导致的开机故障，所以我们首先要排除是不是硬盘连接松动导致。一般台式机都直接打开箱体，从新把硬盘的连接数据线和电源线都拔出来吹一下，然后再插好，如果发现数据线有明显的损坏迹象，我们可以直接换一根硬盘...
From iBMC V316, the CPU and disk alarms will also include the SN and part umber and the mainboard and memory alarms will also include the part number. This alarm is generated when the system failed to read the hard disk VPD information. Alarm object: Disk Attribute Alarm ID Alarm Severi...
Failed to obtain the voltage at arg1 detection point on the left disk backplane. This alarm is generated when the system failed to obtain the disk backplane voltage. This alarm is generated by the following sensor: Mngmnt Health Attribute Alarm ID Alarm Severity Auto Cl...
读盘失败，格式化重做系统试试，也可能是硬盘有坏道的。台式的话可以先查看BIOS里面能不能检测到硬盘，然后看下机箱里面的线有没插好。
Example Copy RLGHNCXA21W 00-12-07 12:01:43 EST EAGLE 35.0.0 ** 0014.0141 ** CARD 1304 SCCP Loading failed: disk read failedAlarm Level: Major Recovery Try the load again. If the problem persists, replace the TDM with the corrupted media. Refer to the Maintenance Manual for card ...
读盘失败，格式化重做系统试试，也可能是硬盘有坏道的。台式的话可以先查看BIOS里面能不能检测到硬盘，然后看下机箱里面的线有没插好。
错误检查:0xB9 CHIPSET_DETECTED_ERROR 错误检查 0xBA:SESSION_HAS_VALID_VIEWS_ON_EXIT 错误检查 0xBB:NETWORK_BOOT_INITIALIZATION_FAILED 错误检查 0xBC:NETWORK_BOOT_DUPLICATE_ADDRESS 错误检查:0xBD INVALID_HIBERNATED_STATE 错误检查 0xBE:ATTEMPTED_WRITE_TO_READONLY_MEMORY 错误检查:0xBF MUTEX_ALREADY_...
Failed to obtain data of the arg1 disk arg2 VPD information. From iBMC V316, the CPU and disk alarms will also include the SN and BOM code and the mainboard and memory alarms will also include the BOM code. This alarm is generated when the system fail...