PC evaluation software for control and measurement of the AD9910 USB interface Graphic user interface (GUI) software with frequency sweep capability for board control and data analysis Factory tested and ready to use 技术与领域 航空航天和防务(2) ...
EVAL-AD9910 EVAL-AD9910 AD9910 评估板 EVAL-AD9910 本页面提供有关评估AD9910的评估板文档和订购信息。 本页面提供有关评估AD9910的评估板文档和订购信息。 AD9910 评估板 | Analog Devices Full-featured evaluation board for the AD9910 PC evaluation software for control and measurement of the AD9910 US...
在淘宝,您不仅能发现AD9910/PCBZ【BOARD EVAL FOR AD9910 1GSPS】开发板 套件 编程器的丰富产品线和促销详情,还能参考其他购买者的真实评价,这些都将助您做出明智的购买决定。想要探索更多关于AD9910/PCBZ【BOARD EVAL FOR AD9910 1GSPS】开发板 套件 编程器的信息,请来
在淘宝,您不仅能发现评估板套件AD9910/PCBZ【BOARD EVAL FOR AD9910 1GSPS】的丰富产品线和促销详情,还能参考其他购买者的真实评价,这些都将助您做出明智的购买决定。想要探索更多关于评估板套件AD9910/PCBZ【BOARD EVAL FOR AD9910 1GSPS】的信息,请来淘宝深入了解吧!
TXT 1.83 K AD9910 Evaluation Board USB Flash Programmer Readme EVB flash readme: This file contains instructions for re-flashing the USB controller on an older eval board so that the evaluation board is compatible with the newer 64-bit USB driver. The USB driver is also 32-bit compatible...
I have been using the AD9910 Eval Board. I am using the on board 25MHz signal.I populated the PLL loop filter components. Their values are R1=43.2ohm C1=330nF C2=15nF I set the charge pump to 387uA. This should correspond to a open loop bandwidth of 50kHz. ...
I have been using the AD9910 Eval Board. I am using the on board 25MHz signal.I populated the PLL loop filter components. Their values are R1=43.2ohm C1=330nF C2=15nF I set the charge pump to 387uA. This should correspond to a open loop bandwidth of 50kHz. ...
EVAL-AD9910 EVAL-AD9910评估板 数据: EVAL-AD9910 EVAL-AD9910 AD9910 评估板 EVAL-AD9910 本页面提供有关评估AD9910的评估板文档和订购信息。 本页面提供有关评估AD9910的评估板文档和订购信息。 AD9910 评估板 | Analog Devices Full-featured evaluation board for the AD9910 PC evaluation software for ...
在淘宝,您不仅能发现AD9910/PCBZ【BOARD EVAL FOR AD9910 1GSPS】的丰富产品线和促销详情,还能参考其他购买者的真实评价,这些都将助您做出明智的购买决定。想要探索更多关于AD9910/PCBZ【BOARD EVAL FOR AD9910 1GSPS】的信息,请来淘宝深入了解吧!
In trying to use the internal Xtal on the AD9910 Eval Board, I attached two 0 Ohms resistors at position R4 and R11. However, I didn't remove C51 and C52 that connects the external clock input. Now when I start the board, DVDD_IO appears be short circuited. The 3.3V power supply ...