No network connectivity and ethtool reports link speed and duplex as unknown: Raw # ethtool eth0 Settings for eth0: Supported ports: [ FIBRE ] Supported link modes: 1000baseT/Full 10000baseT/Full Supported pause frame use: Symmetric Receive-only Supports auto-negotiation: No Advertised link mode...
ethtool是一种用于显示和修改以太网卡设置的Linux命令行工具。使用ethtool eth0可以显示eth0网卡的连接状态参数,包括以下内容: 1. Link detected:表示网卡是否检测到链路连接。如果连接正常,通常会显示为“yes”。 2. Speed:表示网卡的连接速度,如1000Mb/s表示千兆网卡。 3. Duplex:表示网卡的双工模式,如Full表示全...
ethtool ethx 查看支持的速率 实际网卡速率可以看Speed 100Mb/s;问题来了,是不是千兆网卡Speed一定是1000M呢? 不一定哟,网卡速率和网线,交换机端口速率都有关系,看到Auto-negotiation字段了吧,on表示开启 自动协商,插上网线后会两端会自动协商一个都支持的速率; 2. Link detected 代表什么呢? &nb... ...
当涉及到具体操作时,正确识别网络接口并获取其详细的诊断信息是解决问题的关键。首先,可以通过ip link show或ifconfig命令列出所有可用的网络接口,这有助于确定哪个接口对应于特定的物理网卡。一旦确定了目标接口,就可以使用前面提到的ethtool -i和-S选项来进行更深入的检查。 除了上述基本功能外,ethtool 还提供了许多...
ethtool -s eth0 autoneg off speed 100 duplex full # 也可以同时写在一起 ethtool -s eth0 duplex [half|full] # 设置网卡的工作模式,可设置为半双工或全双工 ethtool -G eth0 rx 4096 /ethtool -G eth0 tx 4096 //修改网卡的接收/发送环形参数。
用法:ethtool -s eth0 speed 1000 duplex full autoneg off 效果:将设备号eth0对应的物理端口设置为速率为1000Mbps,全双工工作模式,同时关闭自动协商。 注:若需要永久更改有两种方法: 1. 将上述命令写入/etc/rc.local文件中,开机自动执行; 2. 在/etc/sysconfig/network-scripts/ifcfg-eth0中添加一行ETHTOOL_OP...
Speed,Duplex,CRC 之类的都没问题,基本可以排除物理层面的干扰。 3.2 通过 ifconfig 可以看到 overruns 是否一直增大 for i in `seq 1 100`; do ifconfig eth2 | grep RX | grep overruns; sleep 1; done 这里一直增加 RX packets:346547657 errors:0 dropped:0 overruns:35345 frame:0 ...
ethtool -s eth0 speed [10|100|1000] # 设置网卡的速率,单位是:Mb/s ethtool -s eth0 autoneg [on|off] # 设置网卡是否自动协商 自动协商的内容主要包括工作模式、网卡速率以及流控等参数 ethtool -s ethX [speed 10|100|1000] [duplex half|full] [autoneg on|off] //设置网口速率10/100/1000M、...
Speed,Duplex,CRC 之类的都没问题,基本可以排除物理层面的干扰。 overruns 和 buffer size for i in `seq 1 100`; do ifconfig eth2 | grep RX | grep overruns; sleep 1; done RX packets:346547657 errors:0 dropped:0 overruns:35345 frame:0 ...
若要eth0启动时设置这些参数, 修改文件/etc/sysconfig/network-scripts/ifcfg-eth0 ,添加如下一行: ETHTOOL_OPTS="speed 100 duplex full autoneg off"解决方法二:将ethtool设置写入/etc/rc.d/rc.local之中。 典型用法:查询网络端口位置ethtool -p