hal_eth_init函数是STM32 HAL库中用于初始化以太网外设的函数。它的作用主要是配置以太网MAC控制器、PHY芯片以及相关的GPIO、时钟和中断。在调用此函数之前,通常需要正确配置相关的硬件连接和参数设置。 2. 检查hal_eth_init初始化失败的错误代码或日志信息 初始化失败时,通常会有错误代码或日志信息输出。例如,在STM...
@@ -177,7 +177,9 @@ static esp_eth_handle_t eth_init_internal(eth_device *dev_out) 177177 phy_config.reset_gpio_num=CONFIG_ETHERNET_PHY_RST_GPIO; 178178 179179 // Create new PHY instance based on board configuration 180- #ifCONFIG_ETHERNET_PHY_IP101 ...
int board_interface_eth_init(struct udevice *dev, phy_interface_t interface_type) { u8 *syscfg; u32 value; bool eth_clk_sel_reg = false; bool eth_ref_clk_sel_reg = false; /* Gigabit Ethernet 125MHz clock selection. */ eth_clk_sel_reg = dev_read_bool(dev, "st,eth_clk_sel")...
OEMEthInit is called by the debug Ethernet subsystem as part of EdbgInit processing.If this function returns FALSE, no kernel services are enabled over Ethernet.RequirementsOS Versions: Windows CE 2.10 and later. Header: Halether.h. Link Library: Hal.lib....
OEMEthInit is called by the debug Ethernet subsystem as part of EdbgInit processing.If this function returns FALSE, no kernel services are enabled over Ethernet.RequirementsOS Versions: Windows CE 2.10 and later. Header: Halether.h. Link Library: Hal.lib....
eth_vmxnet3_dev_init()：设备未针对我们的目的进行配置“EN前段时间有哥们在vpp群里分享了基于VPP的src/plugins/linux-cp/插件复制的一个临时插件lcpng，作者做了很多方面的验证和修改，并且后期计划合入到vpp主分支上去。本文主要基于ubuntu20.4.3lts系统搭建环境，验证一下基于lcpng插件和frr bgpd配合测试。
I added to at_eth_init.c: mac_config.sw_reset_timeout_ms = 1000; //increase timeout to 1second phy_config.phy_addr = 1; //lock phy address to 1 (ETH01's address) In factory_param_data.csv I changed: (according to this uart_tx_pin to 2 uart_rx_pin to 4 In the config me...
这个好像是字符乱码了吧，实际状态你用ifconfig查看下网卡信息是否完成更新了（如果最小安装可能用不了这个功能，如果用不了可以通过ip addr来查看）。不过有些版本/etc/init.d/network restart 这个方法可能用不了，只能start和stop。建议使用server network restart和systemctl restart network这两个方法来...
In short, 2/6 of the graphics cards I have installed in my ETH mining server cannot be detected by nvidia-smi. One of them was working just fine on the same PCIe port until I installed a new card on a different port. Now that one is fine, but the old one is having problems. The...
bb_miiphy_init(); #endif #if defined(CONFIG_CMD_NET) { char *s; puts("Net: "); eth_initialize(gd->bd); s = getenv("bootfile"); if (s != NULL) copy_filename(BootFile, s, sizeof(BootFile)); } puts("Net: "); eth_initialize(gd->bd); #endif /* CONFIG_CMD_NET */ ...