MspDeInit and HAL_ETH_MspInit functions. Set the speed and duplex settings: heth.Init.Speed = ETH_SPEED_100M; and heth.Init.DuplexMode = 0x00000800U. Configured the PHY address and enabled interrupts on link status changes: heth.Init.PhyAddress = 1U; HAL_ETH_Start...
Starting installation [ 717][V][esp32-hal-uart.c:575] uartBegin(): UART0 initialization done. [ 732][V][esp32-hal-periman.c:235] perimanSetBusDeinit(): Deinit function for type ETHERNET_RMII (49) successfully set to 0x400d3d30 [ 743][V][esp32-hal-periman.c:235] perimanSetBus...
Depending on the device's CPSW instance, the CPSW peripheral has either 1 (port 1) or 2 (port 1 and port 2) Ethernet port which supports RGMII and RMII interfaces, and a host port (port 0) which supports the internalCommunications Port Programming Interface(CPPI). ...
@@ -327,15 +292,15 @@ esp_err_t ksz8863_ctrl_intf_deinit(void) if (s_ksz8863_ctrl_intf != NULL) {switch (s_ksz8863_ctrl_intf->mode) { case KSZ8863_I2C_MODE:i2c_master_bus_rm_device(s_ksz8863_ctrl_intf->i2c_handle); break; ...
So, static assignment works, but is the device actually connected? Can you ping it if you make a static IP? Can it reach the outside world (eg, sntp)? ESP_ondrej Posts:222 Joined:Fri May 07, 2021 10:35 am Re: Help with ETH - unable to get IP address DHCP ...
如需获取准确内容,请参阅链接中的英语原文或自行翻译。 https://e2e.ti.com/support/processors-group/processors/f/processors-forum/982319/am3359-am3359-prueth-init-deinit-system-lockup器件型号:AM3359 主题中讨论的其他器件:TMDSICE3359 大家好、 我目前正在将基于 Yocto 的发行版从3.0/Zeus 升级到3.1/...
Device下面的这些文件也是同样的隔离方法: 只是鼠标右击弹出的界面有些不同: 注意stm32h7xx_hal_msp.c无需隔离,其它所有的文件全部隔离,stm32h7xx_hal_msp.c对于的隔离配置是STM32CubeMX,如果也隔离了,编译会有问题: 隔离后的效果如下: 7.5.3 RTX5配置 ...
struct eth_device parent; #ifndef PHY_USING_INTERRUPT_MODE rt_timer_t poll_link_timer; #endif /* interface address info, hw address */ rt_uint8_t dev_addr[MAX_ADDR_LEN]; /* ETH_Speed */ uint32_t ETH_Speed; /* ETH_Duplex_Mode */ uint32_t ETH_Mode; ...
MspDeInit and HAL_ETH_MspInit functions. Set the speed and duplex settings: heth.Init.Speed = ETH_SPEED_100M; and heth.Init.DuplexMode = 0x00000800U. Configured the PHY address and enabled interrupts on link status changes: heth.Init.PhyAddress = 1U; HAL_ETH_Start...
config.miiSpeed = imxrt_eth_device.speed; config.miiDuplex = imxrt_eth_device.duplex; /* Set SMI to get PHY link status. */ sysClock = CLOCK_GetFreq(kCLOCK_AhbClk); dbg_log(DBG_LOG, "deinit\n"); ENET_Deinit(imxrt_eth_device.enet_base); ...