// For NodeMCU - use pin numbers in the form PIN_Dx where Dx is the NodeMCU pin designation #define TFT_MISO PIN_D6 // Automatically assigned with ESP8266 if not defined #define TFT_MOSI PIN_D7 // Automatically assigned with ESP8266 if not defined #define TFT_SCLK PIN_D5 // Automa...
esp8266使用esphome接入hass 对于生成配置文件的更改 此处nodemcu泛指集成的开发板,一般十几块钱一块 下方使用的是D1,对应的针脚是GPIO5 esp8266: board: nodemcuv2 binary_sensor: - platform: gpio pin: GPIO5 name: "红外传感器" device_class: motion 针脚定义参考图 参考官方文档 https://esphome.io/compone...
nodemcu模块2(或者nodemcu+arduino nano)、lora模块2、dht11温度传感器*1、杜邦线若干 3案件分析 1块nodemcu作为数据接收端(上位机),接入端一边接收来自远端数据,一边将数据传到homeassistant; 1块nodemcu(或者arduino)作为数据发送端(下位机),发送端一边接入dht11传感器数据,一边将数据发送到远端;上位机与下位机之间...
硬件材料:安信可NodeMCU开发板; SDK版本(非最新版本):3.0.1(78a3e33) 导入步骤: 点击C/C++分支,选择Existing Code as MakeFile Project工程; 复制安装之后的msys32\home\aithinker\ESP8266_NONOS_SDK的路径,import --> Cross Gcc , 并且去掉对应的 C++ 勾勾;如下动图所示: 编译步骤: 项目属性设置,鼠标选中项...
# Example configuration entry esphome: name: livingroom esp8266: board: nodemcuv2 binary_sensor: - platform: gpio name: Pin GPIO17 pin: GPIO17 特殊引脚 GPIO0 控制引导模式 GPIO1 UART TX别针 GPIO2 控制引导模式 GPIO3 UART RX引脚 GPIO6 SDIO/Flash CLK引脚 GPIO7 SDIO/闪存数据0针 GPIO8 SDIO...
#Exampleconfigurationentryesphome:name:livingroomesp8266:board:nodemcuv2binary_sensor:-platform:gpioname:"PinGPIO17"pin:GPIO17特殊引脚GPIO0控制引导模式GPIO1UARTTX别针GPIO2控制引导模式GPIO3UARTRX引脚GPIO6SDIO/FlashCLK引脚GPIO7SDIO/闪存数据0针GPIO8SDIO/闪存数据1针GPIO9SDIO/FlashData2针(仅限qio/qout)...
DDSU电表上面有接线图,下进上出。上面有24 25 AB接入到转换模块ab,然后模块的tx rx错位接入esp8266模块(d1mini),然后将以下代码刷写进去esphome。 substitutions:device_name:ddsu666 esphome:name:chint_power_monitor platform:ESP8266board:nodemcuv2
I'm using Fedora 37 with python 3.11. I've confirmed that the device is present at /dev/ttyUSB0. I'm seeing the following errors: Exception in thread Thread-2: Traceback (most recent call last): File "/usr/lib64/python3.11/threading.py",...
Simple code for ESP-based custom dust sensor using Sharp GP2Y1010AU0F sensor in the Keyestudio KS0196 PM2.5 Dust Sensor Module. esp8266 esp pm25 gp2y1010au0f dust-sensor nodemcu-esp8266 esphome-config esphome esphome-device Updated Feb 4, 2022 C++ Mat931 / esp32-doorbell-bus-interf...
and I don’t want to speculate. You could really use any device, or to simplify the steps, you couldprograman ESP device to automatically connect whenever the AP comes online. I made a 2-line modification to this ESP8266codeand programmed one of my ESP32 NodeMCU devices to automatically ...