系统时间,单位:微秒。 system_get_rtc_time 功能: 查询RTC时间,单位:RTC时钟周期 ⽰示例: 例如system_get_rtc_time返回10 (表⽰示10个RTC周期), system_rtc_clock_cali_proc返回5.75 (表⽰示1个RTC周期为5.75微秒), 则实际时间为10 x 5.75 = 57.5微秒。 注意: system_restart时,系统时间归零,但是RTC...
例如system_get_rtc_time 返回 10 (表⽰示 10 个 RTC 周期), system_rtc_clock_cali_proc 返回 5.75 (表⽰示 1 个 RTC 周期为 5.75 微秒), 则实际时间为 10 x 5.75 = 57.5 微秒。 注意: system_restart 时,系统时间归零,但是 RTC 时间仍然继续。但是如果外部硬件通过 EXT_RST 脚或者 CHIP_EN 脚...
一、原理 ESP8266 设置为 STATION + AP 模式。 STATION 模式又叫做站点工作模式,类似于无线终端,处于 STATION 模式下的 ESP8266,可以连接到 AP。通过 STATION (简称为“STA”)模式,ESP8266 作为客户端连接到路由的 Wi-Fi 信号。 AP 就是 Access Point 接入点。由 ESP8266 自己开启热点,供别的设备接入,组成一...
systemctl restart cron.service#重启crontab 3. 在Arduino中编写单片机的程序 程序在我的Github中 程序中 ssid 改为你局域网Wifi名称,只支持2.4G password为你的密码 mqttServer为你mqtt服务端地址 Arduino 3.1 将开发版通过USB线连接到电脑并安装CH340驱动 3.2 添加ESP8266的库 http://arduino.esp8266.com/stable...
system_restart(); // if(wifi_station_disconnect()) // { // os_printf("\r\n--- 02---\r\n"); // Smart_Config=0; // os_timer_disarm(&OS_Timer_2); // delay_ms(100); // wifi_set_opmode(STATION_MODE); // smartconfig...
("\nsystem_restart\n"); system_restart();//复位 } public_timer_cnt=0; } switch(public_timer_state) { case 0:break; case 1: public_timer_out++; public_timer_cnt1++; if(public_timer_out>=6000)//60S配网超时 { printf("\nsmartconfig_timeout\n"); system_restart();//复位 } if(...
case SYSTEM_EVENT_STA_START: //表示wifi启动就绪 esp_wifi_connect(); break; case SYSTEM_EVENT_STA_GOT_IP: //分配得到IP,就表示已经连上路由器咯 启用wed xEventGroupSetBits(wifi_event_group, CONNECTED_BIT); //设置事件标志位 os_printf("SYSTEM_EVENT_STA_GOT_IP \r\n"); ...
208 system_restart(); 209 } 210 /*** 211 * FunctionName : parse_url 212 * Description : parse the received data from the server 213 * Parameters : precv -- the received data 214 * purl_frame -- the result of parsing the url 215 * Returns...
⽤户可在 user_rf_pre_init 中配置 RF 初始化,RF 设置接⼝为 system_phy_set_rfoption,或者在 Deep-sleep 前调⽤ system_deep_sleep_set_option。如果设置为 RF 不打开,则 ESP8266 Station 及 SoftAP 均⽆法使⽤,请勿调⽤ Wi-Fi 相关接⼝及⽹络功能。RF 关闭时,Wi-Fi 射频功能和⽹络...
如果一个程序段运行时间在触发软件看门狗和触发硬件看门狗复位之间,则可通过 system_soft_wdt_stop () 的方式关闭软件看门狗,在程序段执行完毕后用 system_soft_wdt_restart () 可以通过在程序段中添加 system_soft_wdt_feed () 尝试喂狗在程序段比较长的代码端中。