**ESP8266-NodeMCU开发板驱动 (CP210X) ** http://www.taichi-maker.com/homepage/download/#nodeMCU https://ifwz.lanzouw.com/iNKVPz3on2h 可以上传个blink测试一下板子 点亮nokia5110 参考https://microcontrollerslab.com/nokia-5110-lcd-esp8266-nodemcu-tutorial/ 安装 这两个库 测试代码 点击查看代码 ...
ESP8266-NodeMCU开发板驱动 (CP210X) http://www.taichi-maker.com/homepage/download/#nodeMCU https://ifwz.lanzouw.com/iNKVPz3on2h 可以上传个blink测试一下板子 点亮nokia5110 参考https://microcontrollerslab.com/nokia-5110-lcd-esp8266-nodemcu-tutorial/ 安装 这两个库 测试代码 #include<SPI.h>#inc...
参考https://microcontrollerslab.com/nokia-5110-lcd-esp8266-nodemcu-tutorial/安装 这两个库测试代码点击查看代码 #include <SPI.h> #include <Adafruit_GFX.h> #include <Adafruit_PCD8544.h> Adafruit_PCD8544 display = Adafruit_PCD8544(D4,D3,D2,D1,D0); void setup() { Serial.begin(115200);...
esp8266智能开关灯制作教程一、硬件准备1、硬件工具2、接线图电子接线图:实物接线图:3、ESP8266NodeMcu开发板引脚图nodemcu引脚对应数字:如D0=16;D1=5;D2=4;D3=0。二、配置环境0、安装ESP8266的驱动(1)打开工具包中的esp8266驱动文件,直接傻瓜式安装即可(2)驱动安装成功后,把esp8266通过数据线接入电脑USB口。
I have Lolin NodeMCU V3, I followed,these instructionsand to upload use NodeMCU firmware programmer, you have to hold down the flash button and then press the reset button. That's the only way I go the NodeMCU Firmware programmer to work. ...
Default Config (NodeMCU, Wemos d1 mini, ...) DSTIKE Deauther (without OLED) DSTIKE Deauther v1, v2, v3 DSTIKE Deauther v3.5 DSTIKE Deauther OLED DSTIKE Deauther OLED v1, v1.5 DSTIKE Deauther OLED v1.5S (with RGB) DSTIKE Deauther OLED v2, v2.5, v3 DSTIKE Deauther OLED v3.5, v4 DST...
For the NodeMCU v3 and Adafruit Feather HUZZAH, the location of the RX1 pin is shown in the images below. Many other modules also expose the RX1 pin. Raspberry Pi Since the Raspberry Pi is a 3.3V device, the best practice is to use a logic level converter to shift the 3.3V logic to...
The flasher program comes with default NodeMCU firmware in memory. This is unlikely to be the latest version, but to get started quickly, use the default internal image. Later, you candownload the latest firmware, then select the [Config] tab and choose the new .bin file. Select the 0x7C0...
In this tutorial we receive ADC data and send PWM data to ESP8266 NodeMCU without refreshing webpage. You can do a lot of things with this.
This is a getting started guide for the ESP8266 NodeMCU Wo-Fi module. It also includes a video tutorial. You can use an Arduino or a FTDI programmer to send commands.