3,设置屏幕驱动板端口和ESP8266对应的端口 // For NodeMCU - use pin numbers in the form PIN_Dx where Dx is the NodeMCU pin designation #define TFT_MISO PIN_D6 // Automatically assigned with ESP8266 if not defined #define TFT_MOSI PIN_D7 // Automatically assigned with ESP8266 if not defi...
lambda'return position / 180.0;'# lambda是esphome中一个运算符,没太搞得懂,简单理解就是把后面的计算结果return给前面的参数servo:# 定义一个舵机-id:my_servooutput:pwm_outputmin_level:2.5%# 调整最小脉宽信号max_level:12.5%# 调整最大脉宽信号#pin可按照实际接线情况修改,我这里舵机信号线是用了D0口,...
1、mediaroom-bridge.yaml esphome: name: mediaroom-bridge includes: - uart_read_line_sensor.h logger: level: DEBUG #makes uart stream available in esphome logstream baud_rate: 0 #disable logging over uart uart: id: uart_bus tx_pin: D4 rx_pin: RX baud_rate: 19200 text_sensor: - platfo...
esphome:name:esp01s-1platform:ESP8266board:esp01_1mwifi:networks:ssid:"blue_sky"#改成你的wifi名称password:"720805zzy"#改成你的wifi密码power_save_mode:light#manual_ip:#static_ip: 192.168.50.189#gateway: 192.168.50.1#subnet: 255.255.255.0# Enable fallback hotspot (captive portal) in case wifi...
esphome-esp8266 esp8266使用esphome接入hass 对于生成配置文件的更改 此处nodemcu泛指集成的开发板,一般十几块钱一块 下方使用的是D1,对应的针脚是GPIO5 esp8266: board: nodemcuv2 binary_sensor: - platform: gpio pin: GPIO5 name: "红外传感器" device_class: motion...
esphome:name:node_mcuplatform:ESP8266board:nodemcuv2wifi:ssid:"blue_sky"password:"720805zzy"# Enable fallback hotspot (captive portal) in case wifi connection fails# Enable logginglogger:# Enable Home Assistant APIapi:password:"123"ota:password:"123"output:-platform:esp8266_pwmpin:GPIO2frequency...
网上看各位大神用esp8266 做个各种传感器 接入homeassistant ,实现智能联动 ,忍不住,也买了esp8266模块 dht11温度传感器 雨水感应器 用esphome 编译固件 成功实现 温度和雨水感应器,并接入homeassistant。 并附上yaml 文件 希望对大家有帮助 esphome: name: water friendly_name: water esp8266: board: esp01_1m ...
docker run -d --name='esphome' \--restart=always \-p 6052:6052 \-e TZ="Asia/Shanghai" \-v '/mnt/mmcblk2p4/hass/esphome':'/config':'rw' \esphome/esphome 3、 webui : ip:6052 web_server:port: 80switch:- platform: gpiopin: 14name: "Living Room Dehumidifier" ...
如果设备直接有I2C管脚，试试在yaml中直接定义，参考https://esphome.io/components/sensor/am2320.html?
esphome: name: esp8266-t94 #制定配置文件名称 esp8266: board: esp01_1m #指定芯片类型 # Enable logging logger: # Enable Home Assistant API #与HA整合 api: encryption: key: "RxXAgCVB1/wnoTchfDZpC66MhV2V8hDJf9FWgI45TtE=" ota: #自动升级 password: "28ebd5e9fde077c53a2d12fc09089acc" ...