Adafruit_SSD1306 display(SCREEN_WIDTH, SCREEN_HEIGHT, &Wire, -1);// (-1) 参数表示您的 OLED 显示器没有 RESET 引脚 void testscrolltext(void); //函数声明 void setup() { Serial.begin(115200);//115200 的波特率初始化串行监视器以进行调试 if(!
根据需要设置这些,并使用display.println功能在OLED上显示。 void loop() { DateTime now = rtc.now(); display.clearDisplay(); display.setTextSize(2); display.setCursor(75,0); display.println(now.second(), DEC); 因此,这就是您可以使用 ESP32 在 OLED上显示时间的方式,并且您知道 ESP 以其物联网...
1、建立ssd1306.py文件,该文件是oled12864驱动文件。 # 文件内容如下import timeimport framebuf# register definitionsSET_CONTRAST = const(0x81)SET_ENTIRE_ON = const(0xa4)SET_NORM_INV = const(0xa6)SET_DISP = const(0xae)SET_MEM_ADDR = const(0x20)SET_COL_ADDR = const(0x21)SET_PAGE_ADDR ...
esp32idf点亮oled esp32 lcd显示 前言 之前使用ESP32 来控制TFT屏幕显示动图时,找到现有的工具,需要先将动图gif格式一帧帧转为jpg格式,再将一帧帧的jgp转为hex十六进制格式,整个过程好麻烦。现用python写了脚本,将gif动图,一步生成hex16进制格式.h文件,过程时将gif动图获取到每一帧,然后将每一帧转成16进制...
OLED的显示接口对应,在显示驱动函数中实现。所以我在源库文件(OLEDDisplay.cpp)里添加了像素点清除函数如下所示:当然在OLEDDisplay.h声明也少不了,就不贴代码啦。 voidOLEDDisplay::clearPixel(int16_t x, int16_t y) {if(x >=0&& x <128&& y >=0&& y <64) {switch(color) {caseWHITE: buffer[x...
(WiFi.localIP());// Display IP address on OLEDdisplay.clearDisplay();display.setCursor(0,0);display.println("WiFi connected");display.print("IP: ");display.println(WiFi.localIP());display.display();}voidloop(){// Your loop code here. In this example, the loop does not contain ...
oled = ssd1306.SSD1306_I2C(oled_width, oled_height, i2c) ti=ti+1 try: dht1.measure() print("温度为: " + str(dht1.temperature()) + '℃') print("湿度为: " + str(dht1.humidity()) + '%') tem = int(dht1.temperature()) ...
U.FL for LoRa No shield SiLabs CP2102 ESP32 development board with 0.96 inch OLED display, battery connector, and LoRa (SX1278). Antennas: ESP32 Wi-Fi & Bluetooth uses the MIFA PCB trace and SX1278 LoRa uses an external antenna via the U.FL connector. Pinout from top & from bottom ...
4.2. OLED_show.py脚本代码: '''实验名称:OLED显示屏(I2C总线)版本:v1.0日期:2019.4作者:01Studio'''frommachineimportI2C,Pin#从machine模块导入I2C、Pin子模块fromssd1306importSSD1306_I2C#从ssd1306模块中导入SSD1306_I2C子模块i2c=I2C(sda=Pin(5),scl=Pin(4))#pyBoard I2C初始化:sda--> Y8, scl --...
Section 2. Define the pins that are used to interface with the display here 定义开发板和屏幕引脚之间的接线和引脚对应关系; 常见的屏幕引脚排列组合都可以找到连成组的对应关系,SPI或串口对着自己屏幕引脚丝印找到对应引脚配置是很很容易的; 这里单独强调了有背光调整脚(通常PCB上丝印为BL)、复位脚(RST)的使用...