//#define TFT_RST -1 // Set TFT_RST to -1 if the display RESET is connected to NodeMCU RST or 3.3V// ### EDIT THE PIN NUMBERS IN THE LINES FOLLOWING TO SUIT YOUR ESP32 SETUP ###// For ESP32 Dev board (only tested with ILI9341 display)// The hardware SPI can be mapped to...
display.setTextSize(2); display.setCursor(40,0); display.println(now.minute(), DEC); display.setTextSize(2); display.setCursor(0,0); display.println(now.hour(), DEC); display.setTextSize(1); display.setCursor(0,15); display.println(now.day(), DEC); display.print(daysOfTheWeek[now...
之前使用ESP32 来控制TFT屏幕显示动图时,找到现有的工具,需要先将动图gif格式一帧帧转为jpg格式,再将一帧帧的jgp转为hex十六进制格式,整个过程好麻烦。现用python写了脚本,将gif动图,一步生成hex16进制格式.h文件,过程时将gif动图获取到每一帧,然后将每一帧转成16进制hex文件可以直接使用,下面介绍脚本,和基于...
super().__init__(self.buffer, self.width, self.height, framebuf.MONO_VLSB) self.init_display() def init_display(self): for cmd in ( SET_DISP, # display off # address setting SET_MEM_ADDR, 0x00, # horizontal # resolution and layout SET_DISP_START_LINE, # start at line 0 SET_...
在Tools 中选择分区方案 “Default 4MB with spiffs”。 插入ESP32。 单击Tools 并选择 “ESP Sketch Data Upload”。 如果数据上传失败,可能是你已经打开了串行监视器。如果发生这种情况,请关闭串行监视器后再重试。 Bluetooth-System-Monitor.ino 在Github 上,你可以找到完整的源代码: ...
1,display.h,display.c 这里就是实现了TFTLCD移植到LVGL里面,然后TFTLCD的使用以及移植到LVGL参考前面的博客。 #include"display.h"#include<TFT_eSPI.h>/*TFT pins should be set in path/to/Arduino/libraries/TFT_eSPI/User_Setups/Setup24_ST7789.h*/TFT_eSPI tft=TFT_eSPI();staticlv_disp_buf_t ...
Section 2. Define the pins that are used to interface with the display here 定义开发板和屏幕引脚之间的接线和引脚对应关系; 常见的屏幕引脚排列组合都可以找到连成组的对应关系,SPI或串口对着自己屏幕引脚丝印找到对应引脚配置是很很容易的; 这里单独强调了有背光调整脚(通常PCB上丝印为BL)、复位脚(RST)的使用...
当然,咱们用封装过的 iot 框架的目的,就是牺牲性能来换取开发应用的便捷,所以 .NET Nano 已经封装好了,咱们不用去写寄存器。使用 DisplayControl 类(nanoFramework.UI 命名空间)就能往 LCD 屏里写入颜色。这个类公开的都是静态成员,不用实例化。 1、初始化引脚功能。由于 ESP32 的引脚是复用的,所以对于 SPI 的...
display.display(); delay(500); // Pause for 2 seconds display.setTextSize(1); display.setTextColor(WHITE); display.setRotation(0); } void loop() { sensors_event_t a, g, temp; mpu.getEvent(&a, &g, &temp); display.clearDisplay(); ...
I2C.h"// create an LCD object (Hex address, # characters, # rows)// my LCD display in on...