然后我到CP210x USB to UART Bridge VCP Drivers上,下载安装驱动CP210x Universal Windows Driver v10.1.10之后就能下载了 下载完成 串口调试 点击打开调试窗口 查看打印: 3.2 使用ESP-IDF CMD烧写 烧录前先配置模组的flash大小: 输入命令idf.py menuconfig打开配置界面 进入Serial flasher config,按需将Flash size改...
下载地址:https://doc.itprojects.cn/0006.zhishi.esp32/01.download/esp32usbDriver.zip 下载后安装即可 5. 烧录MicroPython到EPS32 在弹出的框中点击下图所示位置 会再次弹出1个框 在上图序号1处选择,串口。只要安装了我提供的驱动,那么会看到如下的名字(COM后的序号不一样没事) 注意:ESP32此时要链接USB开机...
下载地址:https://doc.itprojects.cn/0006.zhishi.esp32/01.download/esp32usbDriver.zip 五、烧录MicroPython到ESP32 打开Thonny软件 在弹出的框中点击下图所示位置 会再次弹出1个框 在上图序号1处选择,串口。只要安装了我提供的驱动,那么会看到如下的名字(COM后的序号不一样没事) 注意:ESP32此时要链接USB开机...
Connect the UART port of the board to the computer using a USB cable Code analysis echo_task(): Firstly, UART parameters were configured, including baud rate, data bits, parity bits, stop bits, and hardware flow control, etc. Then install the UART driver, set the UART pins, and allocate...
8. USB Type-C port USB to serial port for program flashing and log printing 9. RESET button 10. BOOT button Press before reset to enter download mode Interfaces Type-C interface: The development board uses the CH343P chip to convert USB to UART, and connects the UART_TXD (GPIO43) and...
下载地址:https://micropython.org/download/esp32/ 为了能够将程序下载(烧录)到ESP32中,需要安装驱动 下载地址:https://doc.itprojects.cn/0006.zhishi.esp32/01.download/esp32usbDriver.zip 五、烧录MicroPython到ESP32 打开Thonny软件 在弹出的框中点击下图所示位置 ...
I (311) VCP example: Installing USB Host I (341) VCP example: Installing CDC-ACM driver I (341) VCP example: Opening CH340 device I (741) VCP example: Setting up line coding I'll run some tests and see how the comms are, I'll report back with any remarks. Either way, thanks fo...
For ESP32 wired connections, use USB 3.1 or lower, or use a USB hub to connect your ESP32 Bluetooth adapter. USB 3.2 may cause connection issues. Once everything is ready, enable the External device in the Virtual controller settings, and click on the icon in the lower-left corner (near...
使用USB转TTL-CH340 连接 ESP32-CAM,用flash_download_tool,把micropython 固件写入 0x1000。模式选DIO,波特率可能需要改成921600,如果默认的115200不成功的话。点击下载之后,如果进度条一直不动,则按一下ESP32-CAM上的RST按钮。 另外,最开始直接用thonny刷入ESP32-CAM的固件,没能成功(ESP32可以直接用thonny刷入...
(supports up to 3 meter sensitivity when playing music), DSP chip for handling the 4-mic array input, phone jack, left & right speaker output ports, audio driver chip, DC/DC boost power supply, power switch, battery connector, USB power input port, USB connectivity port, UART headers, ...