我们打开目录USBCAN(CAN-I分析仪)\usb driver 双击运行: 选择菜单栏Device->Load Preset Device,对话框内选择zadia_usbcan1.cfg并打开。 配置文件zadia_usbcan1.cfg打开后,效果如图 不要填写任何东西, 点击”Install Driver“。之后安装成功。 有些情况下,需要重新插拔一下USBCAN模块,才能使用。
W (1218) USB_STREAM: Audio control interface NOT found E (1218) USB_STREAM: ./managed_components/espressif__usb_stream/usb_stream.c:3125 (_uvc_uac_device_enum):Descriptor Parse Result: No matching configurations E (1219) USB_STREAM: ENUM Stage CHECK_FULL_CONFIG_DESC, Failed W (1219) US...
I (1049) UVC_STREAM: Port speed = 1 I (1049) UVC_STREAM: Set Device Addr = 1 I (1049) UVC_STREAM: Set Device Addr Done I (1049) UVC_STREAM: Set Device Configuration = 1 I (1059) UVC_STREAM: Set Device Configuration Done
tusb_serial_device CMakeLists.txt README.md pytest_usb_device_serial.py host cdc cdc_acm_host README.md cdc_acm_vcp README.md hid README.md msc README.md pytest_usb_host_msc.py usb_host_lib README.md uvc README.md sdkconfig.defaults ...
After uploading the code, use the "HY2.0 2P to DuPont male head 2P red-black 10cm" cable to connect the CAN H and CAN L pins of the ESP32-S3-Touch-LCD-4.3 to theUSB-CAN-A. Connect the USB-CAN-A to the computer and open theUSB-CAN-A_TOOL_2.0 upper computer software. Select ...
ffmpeg -f dshow -i video="UVC Camera" -vcodec libx264 -acodec copy -preset:v ultrafast -tune:v zerolatency -f flv rtmp://127.0.0.1:1935/live/UVC 1. 2. 3. gstreamer USB摄像头直接输出H264帧,推流 gst-launch-1.0 -v v4l2src device=/dev/video0 ! 'video/x-h264, width=640, height...
- This can be called elsewhere if necessary as long it is called after :cpp:func:`usb_host_install`. 3. Device 1 connects and is then enumerated. - Each registered client (in this case Client 1 and Client 2) are notified of the new device by way of the :cpp:enumerator:`USB_HOST_...
I was trying out the uvc example project by connecting the webcam to a custom PCB with the ESP32S3 chip. I used a USB breakout board to connect the webcam to the ESP32S3. I connected D- to GPIO19 and D+ to GPIO20. I connected VBUS to 5V on the breakout board and GND pin to...
I was trying out the uvc example project by connecting the webcam to a custom PCB with the ESP32S3 chip. I used a USB breakout board to connect the webcam to the ESP32S3. I connected D- to GPIO19 and D+ to GPIO20. I connected VBUS to 5V on the breakout board and GND pin to...
关于uvc以及lcd初始化报错问题 by18942487161» Sun Sep 10, 2023 2:40 pm 0 2474 by18942487161 Sun Sep 10, 2023 2:40 pm RF校准能否校准晶振 bykaisey» Sat Sep 02, 2023 3:01 am 2 11134 bykaisey Sat Sep 09, 2023 7:58 am esp event 的时序逻辑是怎样的?