3. 他的串口发送/接收引脚是固定的,是IO1和IO3。 Serial串口的实际工作流程: 1.ESP32开发板上电以后,会进入APP运行模式。 2.ESP32内置操作系统会在运行阶段,不断检测Serial串口的状态。 3.当检测到串口是未连接状态,并且这个时候有烧录请求命令时(点击Arduino软件的烧录上传按钮),这时Serial串口会转换到程序下载...
("\t"); // 0 Serial.print("\n"); */ // configure Arduino LED pin for output pinMode(LED_PIN, OUTPUT); } void loop() { // read raw accel/gyro measurements from device accelgyro.getMotion6(&ax, &ay, &az, &gx, &gy, &gz); // these methods (and a few others) are also...
int potpin = 0;//模拟接口0,连接温度传感器 void setup(){ Serial.begin(9600); } void loop(){ int val; int det; val = analogRead(potpin);//读取模拟值 det = (125 * val) >>8; //将模拟值转换为温度 Serial.print("TEP:"); Serial.print(det); Serial.println("C"); delay(500); }...
// pin=中断引脚,function=中断函数,mode=中断触发模式 attachInterrupt(pin, function, mode); 如果在程序运行过程不需要使用外部中断了,可以用中断分离函数来取消这一中断设置: detachInterrupt(interrupt); detachInterrupt(Pin);。 3、示例 void setup() { // 初始化日志打印串口 Serial.begin(115200); // 配置...
这些准备工作完成后,还需要在setup()中使用attachInterrrupt()函数对中断引脚进行初始化配置,以开启arduino的外部中断功能,其用法如下: (1)attachInterrupt(interrupt, function,mode)。 功能:对中断引脚进行初始化配置 参数: interrupt,中断编号,注意,这里的中断编号并不是引脚编号 ...
}voidsetup(){// 启动串口调试输出Serial.begin(115200);// 初始化 ESP32 的串口2Serial2.begin(921600);// 配置串口2的RX引脚为中断模式pinMode(16, INPUT_PULLUP); attachInterrupt(digitalPinToInterrupt(16), serial2ISR, FALLING); }voidloop(){// do nothing} ...
Arduino-ESP32 LEDC API - ledcSetup() 该函数用于启动 LEDC ,指定通道、频率、分辨率。 uint32_tledcSetup(uint8_tchannel,uint32_tfreq,uint8_tresolution_bits); channel 选择 LEDC 通道。 freq 选择 pwm 的频率。 resolution_bits 选择 LEDC 通道的分辨率。
可以看到第二个方法是传入一个interrupt的中断编号,但是ESP32上面的中断编号,不在官方资料中,所以我们只有需要第一个方法来进行引脚和中断函数的关联,当然了可能最后一个也是可以,只是此处我没有尝试,感兴趣的可以进行尝试, 在mode中,Arduino是支持五种模式,第一种为LOW,,看翻译我们知道,这个是在电平处于低电平时会...
Serial.printf("按键中断触发"); } voidsetup() { Serial.begin(9600); attachInterrupt(0,func1,FALLING); } voidloop() { } 2. 关闭引脚中断 detchInterrupt(pin); 无返回值 四. 时间统计函数 1. 开机至今的毫秒数 millis millis() 返回值是unsigned long 类型, 大约50天溢出一次 ...
ESP32 GPIO Interrupt Pins All ESP32 GPIO pins are interrupt-capable pins. You can enable the interrupt functionality to any GPIO input pin using this function from the Arduino Core. 1 attachInterrupt(GPIO_pin,ISR,Event); We’ll get into the details of this function and how to use it in ...