ESP32-S3-DevKitC-1 管脚布局 由于这个程序控制比较简单,就不赘述了,直接看程序。 二、程序 #include"freertos/FreeRTOS.h" #include"freertos/task.h" #include"driver/ledc.h" #defineLED_PIN 6 #defineLED_PIN_SEL (1ULL<<LED_PIN) /** * @brief 配置引脚功能 */ voidbsp_led_init(void) { g...
ESP32-S3-DevKitC-1开发板RGB灯使用说明 2236观看 1弹幕 资料获取: esp32离线包:https://pan.baidu.com/s/1DFR2X6stro4PTXMg9rOrow?pwd=b4u0 先下载,再解压后打开.exe文件会自动读条安装,读条结束后重启IDE即可,只需下载esp32,不需要esp8266。
Addressable RGB LED, driven by GPIO48. Turns on when the USB power is connected to the board. Start Application Development Before powering up your board, please make sure that it is in good condition with no obvious signs of damage. Required Hardware ESP32-S3-DevKitC-1 USB 2.0 cable (...
[env:esp32-s3-devkitc-1] platform = espressif32 board = esp32-s3-devkitc-1 framework = arduino lib_deps = # RECOMMENDED # Accept new functionality in a backwards compatible manner and patches fastled/FastLED @ ^3.7.1 build_flags += -DARDUINO_USB_CDC_ON_BOOT=1 -DARDUINO_USB_MODE=1...
增加2 只 LED 灯,方便代码调试。 4.5 增加短路保护 板载一支可恢复保险丝,当电路板电源短路时,自动断电,确保开发板不会被烧毁,对新手友好。 5 产品性能 5.1 搭载乐鑫原装模组 ESP32-S3-WROOM-1 乐鑫官方模组,性能强悍,资源丰富。 5.2 可选存储配置
ESP32-S3-DevKitC-1是一款入门级开发板，搭载Wi-Fi+Bluetooth®LE模组 ESP32-S3-WROOM-1，板上模组的大部分管脚均已引出至开发板两侧排针，开发人员可根据实际需求，轻松通过跳线连接多种外围设备，也可将开发板插在面包板上使用。ESP32-S3-DevKitC-1开发板应用场景：ESP32-S3-WROOM-1是一款通用型Wi-Fi+低...
A while back I purchased an ESP32-S3-DevKitC-1 (version 1.0), which has an on-board RGB LED controlled via GPIO48. I understand there has been a hardware revision to resolve a 1.8v SPI supply issue (which GPIO47/48 use instead of the regular GPIO supply due to PSRAM) and hence th...
刚入手一块ESP32-S3-DevKitC-1,想先跑example的程序试试看。HelloWorld没问题,Blink例程异常,有打印,灯不闪烁。 检查程序,环境,板子硬件等等中间过程不提,最终发现原因: 板子上的实际硬件情况是,是GPIO38接到的LED灯,而不是GPIO48!!! blink example project上 却是 #define CONFIG_BLINK_GPIO 48这么设置的。
1.led_strip_init 2.ws2812_set_pixel 四、程序示例 前言 这里使用的是乐鑫的 ESP32-S3-DevKitC-1 开发板,搭载的是 Wi-Fi + Bluetooth® LE 模组 ESP32-S3-WROOM-1 ,内置芯片配置是 ESP32-S3FN16R8,开发板组件包含一下内容 接着给大家讲的是 esp-idf 对 RGB-LED的驱动 ...
[env:esp32dev] platform = https://github.com/tasmota/platform-espressif32/archive/refs/heads/IDF44/ESP32-S3.zip board = esp32-s3-devkitc-1 framework = arduino 写测试代码 查原理图可知板载LED有2个,分别为IO38和IO39 将以下代码填入至main.cpp 点击查看代码 highlighter- Arduino #include <Ardui...