运行idf.py -p PORT flash monitor来构建和flash项目. 这个命令将查找分区表是否具有ota_data分区(在我们的示例中),然后ota_data将擦除为initial。它允许从一个工厂分区运行新加载的应用程序。 (要退出串行监视器,请键入Ctrl-]) 有关配置和使用ESP-IDF构建项目的完整步骤,请参阅入门指南 示例输出 HTTPS服务器运...
0xf000 build.esp-box-3/ota_data_initial.bin \ 0x20000 build.esp-box-3/esp32-graphical-bootloader.bin \ 0x220000 apps/tic_tac_toe/build.esp-box-3/tic_tac_toe.bin \ 0x4E0000 apps/wifi_list/build.esp-box-3/wifi_list.bin \ 0x7A0000 apps/calculator/build.esp-box-3/calculator.bin \...
运行idf.py -p PORT flash monitor 来构建和flash项目. 这个命令将查找分区表是否具有ota_data分区(在我们的示例中),然后ota_data将擦除为initial。它允许从一个工厂分区运行新加载的应用程序。 (要退出串行监视器,请键入 Ctrl-]) 有关配置和使用ESP-IDF构建项目的完整步骤,请参...
在终端输入如下命令开始烧写: esptool.py --chip esp32 --port /dev/tty.SLAB_USBtoUART --baud 921600 --before default_reset --after hard_reset write_flash -z --flash_mode dio --flash_freq 40m --flash_size detect 0xd000 ota_data_initial.bin 0x1000 bootloader.bin 0x10000 esp32devkitc-...
此时可使用 esptool.py -p /dev/ttyUSB0 -b 460800 --before default_reset --after no_reset --chip esp32 write_flash --flash_mode dio --flash_size keep --flash_freq 40m 0xf000 build/partition_table/partition-table.bin 0x20000 build/ota_data_initial.bin 0x30000 build/console.bin 0x...
运行idf.py -p PORT flash monitor来构建和flash项目. 这个命令将查找分区表是否具有ota_data分区(在我们的示例中),然后ota_data将擦除为initial。它允许从一个工厂分区运行新加载的应用程序。 (要退出串行监视器,请键入Ctrl-]) 有关配置和使用ESP-IDF构建项目的完整步骤,请参阅入门指南 ...
D:\Users\Wind\esp\tinyuf2-espressif_saola_1_wrover-0.5.1>esptool --chip esp32s2 -p com9 -b460800--before=default_reset --after=no_reset write_flash --flash_mode dio --flash_freq80m --flash_size4MB0x8000 partition-table.bin0xe000 ota_data_initial.bin0x1000 bootloader.bin0x2d0000 ...
本指南是在您已執行 Espressif ESP32-DevKitC 及 ESP-WROVER-KIT 入門 ,及 無線更新事前準備 之步驟的前提下,撰寫而成。在您嘗試 OTA 更新之前,建議您執行 FreeRTOS 入門中所述的 MQTT 示範專案,以確保您的主機板和工具鏈設定正確。
adress = ["0x0", "0x10000", "0x40000", "0x32000"] binaries = ["bootloader_signed_encrypted.bin", "partition-table_signed_encrypted.bin", "esp32_evse_signed_encrypted.bin", "ota_data_initial_signed_encrypted.bin"] for i in range(0, len(binaries)): bins = [addresses[i], binaries...
If you want to rollback to thefactoryapp after the upgrade (or to the first OTA partition in case thefactorypartition does not exist), run the commandidf.py erase_otadata. This restores theota_datapartition to its initial state. Note:This assumes that the partition table of this project ...