Adafruit_NeoPixel pixels = Adafruit_NeoPixel(NUMPIXELS, PIN, NEO_GRB + NEO_KHZ800); // 新建组件对象 BlinkerRGB RGB1("RGB"); BlinkerButton button1("num-abc"); int LED_R=0,LED_G=0,LED_B=0,LED_Bright=180;// RGB和亮度 bool WIFI_Status = true; void SET_RGB(int R,int G,int B...
ESP_LOGI(TAG,"PWM to max %d\n", LEDC_TEST_DUTY); // 循环渐变每个LED,这里只有一个 for (ch = 0; ch < LEDC_TOTAL_NUM; ch++) { // 配置LEDC定时器 ledc_set_fade_with_time( ledc_channel[ch].speed_mode, ledc_channel[ch].channel, LEDC_TEST_DUTY, LEDC_TEST_FADE_TIME); // 开始...
But …I like when I give the ESP32 power both led’s are going on I changed False in True for both led’s , with a good result. But when I pressed the button green and red going on, pressing again both are off ??? bool buttonDown_2 = false; bool ledOn_2 = true; bool butt...
In the above circuit diagram,GPIO22is connected with an anode pin of LED, and another pin of LED is connected with ground through a 330ohm resistor. you can check theLED blinking tutorialfor more information about it. Next push button one terminal is connected with 3.3 volts of ESP32 and ...
支持多种传感器和执行器,如温湿度传感器、继电器、LED 控制等。 自动更新: 通过OTA(空中下载)更新设备固件,无需物理连接设备即可进行固件升级。 强大的功能: 支持复杂的自动化逻辑、脚本和定时任务。 支持Wi-Fi 和蓝牙连接,适应多种应用场景。 总的来说,通过ESPhome,可以在网页上在线编译ESP系列的固件,并且通过有线...
// Turn off LED before going to sleepdigitalWrite(LED_GPIO_NUM, LOW); esp_deep_sleep_start; //进入深度睡眠} 处理按键:按钮逻辑检查短按(捕捉图像)和长按(进入深度睡眠)。 cppCopy codevoid handleButtonPress {if (isButtonPressed) {if (lastPressTime == 0) {lastPressTime = millis; // 记录...
int buttonState = 0; void setup() { Serial.begin(115200); btStop(); // turn off bluetooth pinMode(ledPin, OUTPUT); pinMode(buttonPin, INPUT); connectWifi(); } void loop() { if ((WiFi.status() == WL_CONNECTED)) { buttonState = digitalRead(buttonPin); ...
测试按键GPIO7点亮LED灯, GPIO9关闭LED灯。测试正常! 1.1.2 ESP32-C3应用程序启动流程(更正上面错误说法!) 对于文中以前提到的使用了FreeRTOS ,但是没有开始调度的说法,是错误的!进行改正! 函数app_mian其实只是一个FreeRTOS的一个任务! 系统跑到app_mian的时候早就开始了调度!!!
fix(zigbee): Enable the internal pull-up resistor for BUTTON_PIN by @lboue in #10491 Tone Adds setToneChannel() implementation by @SuGlider in #10305 OpenThread OpenThread Example Improvement by @SuGlider in #10299 Matter feat(matter): initial commit with arduino matter lib by @SuGlider ...
This repository contains the software, schematics, and 3D printing files for a bedside lamp with various modes controlled by a button. It includes details on hardware components, software installation using PlatformIO or Makefile, and 3D printing instructions esp32 3d-printing stl-files ws2812b vl...