#ifdef CONFIG_EXAMPLE_CONNECT_WIFI //esp_event_handler_register 用来将 IP_EVENT_STA_GOT_IP 事件加入上面由 esp_event_loop_create_default创建的事件处理任务中 //当接收到IP_EVENT_STA_GOT_IP 事件时,执行connect_handler函数 //也就是说,当连接wifi成功,station模式下成功分配到ip后,执行connect_handler...
.channel = EXAMPLE_ESP_WIFI_CHANNEL, // 设置为1~13,表示从指定的通道开始扫描,然后再连接AP。如果AP的通道未知,则设置为0。 .password = EXAMPLE_ESP_WIFI_PASS, // wifi 密码 .max_connection = EXAMPLE_MAX_STA_CONN, // 允许连接的最大站数,默认4,最大10 .authmode = WIFI_AUTH_WPA_WPA2_PSK...
*/ ESP_ERROR_CHECK(example_connect()); 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 2.修改CMakefile.txt 文件 在工程文件目录下,打开CMakefile文件并加入以下内容: set(EXTRA_COMPONENT_DIRS $ENV{IDF_PATH}/examples/common_components/protocol_examples_common) 1. 3.运行idf.py menuco...
(4670)esp_netif_handlers: example_connect: sta ip:192.168.1.192,mask:255.255.255.0,gw:192.168.1.1I(4670)example_connect: Got IPv4 event:Interface"example_connect: sta"address:192.168.1.192I(5670)example_connect: Got IPv6 event:Interface"example_connect: sta"address:fe80:0000:0000:0000:7e9e:...
ESP_ERROR_CHECK(example_connect());//wifi连接函数,WiFi信息在menuconfig配置 #ifdefCONFIG_EXAMPLE_IPV4 xTaskCreate(tcp_server_task,"tcp_server",4096,(void*)AF_INET,5,NULL);//创建一个tcp_server的任务 #endif #ifdefCONFIG_EXAMPLE_IPV6 xTaskCreate(tcp_server_task,"tcp_server",4096,(void*)AF_IN...
I (3583) example_connect: - IPv6 address: fe80:0000:0000:0000:7ae3:6dff:fe09:5350, type:ESP_IP6_ADDR_IS_LINK_LOCAL STA的IP地址为92.168.3.65 4. 浏览器测试 在浏览器地址栏输入http://192.168.3.65 上传文件 选择一个文件: 点击Upload: ...
{esp_wifi_connect();}elseif(event_base==WIFI_EVENT&&event_id==WIFI_EVENT_STA_DISCONNECTED){if(s_retry_num<EXAMPLE_ESP_MAXIMUM_RETRY){esp_wifi_connect();s_retry_num++;ESP_LOGI(TAG,"retry to connect to the AP");}else{xEventGroupSetBits(s_wifi_event_group,WIFI_FAIL_BIT);}ESP_LOGI...
打开wifi_connect_default.c 填写家里或手机的wifi热点名称和密码 #defineCONFIG_EXAMPLE_WIFI_SSID"2.4G wifi名称"#defineCONFIG_EXAMPLE_WIFI_PASSWORD"wifi密码" mg90s舵机默认是90度,安装塑料的转子在90度时贴合到灯的开关侧边 默认开灯是先转动到90度300ms后转到45度500ms后转动回90度 ...
The sample code will use a public MQTT server to connect, and the public MQTT server does not require a username and password. If you create a deployment, please refer to Default Authentication to set username and password. c // WiFi Credentials const char *ssid = "WIFI_SSID"; // Replac...