ESP_ERR_NOT_FOUND when esp_intr_allocby SvanteKaiser » Fri Apr 12, 2024 3:53 pm I get an error when trying to configure an interrupt for DMA. When I use i2s_read outside the interrupt everything works fine, so it's not a problem with microphones or I2S configuration....
(ETS_SPI2_INTR_SOURCE) and whenever any byte I receive from the master, control goes to receive ISR and do some task for that I am using esp_intr_alloc(ETS_SPI2_INTR_SOURCE, ESP_INTR_FLAG_SHARED, spi_slave_isr_handler, &t, &SPI_intr) but I am getting error like ESP_ERR_NOT_...
ESP_INTR_FLAG_SHARED:在多个处理器上共享中断。 ESP_INTR_FLAG_LEVEL1:在级别 1 中分配中断处理程序。 具体可参照 esp_intr_alloc.h 文件中的 ESP_INTR_FLAG_ 相关配置项* 在这个配置项中,主要是将 MOIS 和 MISO 以及 SCLK 三个引脚设置好,在他的可以忽略(如果需要使用自定义缓冲区,则可以设置max_transfe...
esp_err_t esp_intr_alloc( int source, //外部中断源,共计62个外部中断源 int flags, //ESP_INTR_FLAG_LEVEL1~6: 1为最低优先级 6为最高优先级; ESP_INTR_FLAG_SHARED:共享中断; ESP_INTR_FLAG_EDGE:边沿触发中断 intr_handler_t handler, //中断句柄,当优先级大于3时为NULL,因为大于3级不能被C...
Espressif IoT Development Framework. Official development framework for Espressif SoCs. - esp-idf/components/esp32/include/esp_intr_alloc.h at 8bc19ba893e5544d571a753d82b44a84799b94b1 · espressif/esp-idf
*/esp_err_tgpio_isr_register(void(*fn)(void*),void*arg,intintr_alloc_flags,gpio_isr_handle_t*handle);/** * @brief 在GPIO上启用上拉。 * * @param gpio_num GPIO编号 * * @return * -ESP_OK成功 * -ESP_ERR_INVALID_ARG参数错误 ...
#include<stdio.h>#include<stdlib.h>#include"freertos/FreeRTOS.h"#include"freertos/task.h"#include"freertos/queue.h"#include"freertos/timers.h"#include"driver/gpio.h"#include"esp_intr_alloc.h"#include"esp_log.h"#include"driver/mcpwm.h"// #include "soc/mcpwm_periph.h"#include"soc/mcp...
esp_err_t gpio_install_isr_service( int intr_alloc_flags ) 函数说明 使用该函数,ISR服务将提供全局GPIO的ISR,并通过gpio_isr_handler_add()函数注册各个引脚处理程序 参数如下: 登录后复制intr_alloc_flags:中断的类型 GPIO中断注册函数 ...
esp_intr_alloc(ETS_I2S0_INTR_SOURCE, ESP_INTR_FLAG_LEVEL1, i2s_in_isr, NULL, NULL); } 注意事项 中断延迟:确保中断服务函数(ISR)尽可能简短,避免阻塞。复杂操作应放在任务(Task)中处理。 双缓冲区机制:通常需要多个 DMA 缓冲区交替使用,以实现连续数据流。
.intr_alloc_flags=ESP_INTR_FLAG_LEVEL1, .dma_buf_count=2, .dma_buf_len=1024, .use_apll=false, .tx_desc_auto_clear=false, .fixed_mclk=0};//install and start i2s driveri2s_driver_install(I2S_NUM_0, &i2s_config,4, &i2s_queue);//init ADC padi2s_set_adc_mode(ADC_UNIT_1, ADC...