#include<Wire.h>// Only needed for Arduino 1.5 and earlier#include"SSD1306Wire.h"// Initialize the OLED displaySSD1306Wiredisplay(0x3c,1,0, GEOMETRY_128_32);boolshowHelloWorld =true;// 初始显示 "hello world"intpercentage =1;// 从 1% 开始unsignedlonglastUpdate =0;// 记录上次更新时间cons...
新建一个项目: #include<Wire.h> // Only needed for Arduino 1.6.5 and earlier#include"SSD1306Wire.h"// Initialize the OLED display using Arduino Wire:SSD1306Wiredisplay(0x3c,1,0,GEOMETRY_128_32);voidsetup(){// put your setup code here, to run once:Serial.begin(115200);//...
void OLEDDisplay::clearPixel(int16_t x, int16_t y) 显示, 显示buf区的内容 display.displayvoid SSD1306Wire::display() 把显示屏关掉 display.displayOff(); 把显示屏打开 display.displayOn(); 深度睡眠后恢复 display.allocateBuffer(); //使用它可以在深度睡眠后恢复而不重置显示(init()会做什么)。
Adafruit_MPU6050 mpu; //创建显示对象,就是我们的oled显示屏,显示像素为128x32,对象名为display。 Adafruit_SSD1306 display = Adafruit_SSD1306(128, 32, &Wire); void setup() { //初始化串行监视器的波特率为115200。 Serial.begin(115200); // while (!Serial); Serial.println("MPU6050 OLED demo");...
display.drawString(0, 0, "hello world");display.display; }voidloop{}效果:比如现在我想要在显示"hello world"之后从1%到100%循环显示。代码如下:#include<Wire.h> // Only needed for Arduino 1.5 and earlier#include"SSD1306Wire.h"// Initialize the OLED displaySSD1306Wire display(0x3c, 1, 0, ...
2.0.96寸oled屏模块 oledp屏的spi接线有六针和七针的,其实没什么区别,片选C/S不接就是六针了,RST与D/C两个引脚也可以使用普通IO,程序里满足电平条件就行,这里使用板子硬件SPI2资源。 六针七针: GND — 接地端口 VCC —接3.3V电源端口 SCL(D0) — SK时钟信号端口 PB13 SDA (D1) — MOSI数据端口 ...
初始化oled: display.init(); 垂直翻转屏幕(把屏幕显示倒转180°): display.flipScreenVertically(); 设置字体大小: display.setFont(ArialMT_Plain_24);//最后的数字是字体的大小 显示字符串: display.drawString(x, y, "Hello World"); 在每次绘制完后都要调用显示函数: ...
esp32idf点亮oled esp32 lcd显示 前言 之前使用ESP32 来控制TFT屏幕显示动图时,找到现有的工具,需要先将动图gif格式一帧帧转为jpg格式,再将一帧帧的jgp转为hex十六进制格式,整个过程好麻烦。现用python写了脚本,将gif动图,一步生成hex16进制格式.h文件,过程时将gif动图获取到每一帧,然后将每一帧转成16进制...
Adafruit_SSD1306 display(OLED_MOSI, OLED_CLK, OLED_DC, OLED_RESET, OLED_CS); 在设置函数中,我们将调用一个函数rtc.adjust(DateTime(__DATE__,__TIME__)),它将根据我们的PC时间设置时间。 void setup() { Serial.begin(9600); if (! rtc.begin()) { ...
1、建立ssd1306.py文件,该文件是oled12864驱动文件。 # 文件内容如下import timeimport framebuf# register definitionsSET_CONTRAST = const(0x81)SET_ENTIRE_ON = const(0xa4)SET_NORM_INV = const(0xa6)SET_DISP = const(0xae)SET_MEM_ADDR = const(0x20)SET_COL_ADDR = const(0x21)SET_PAGE_ADDR ...