.name ="periodic_gui"};esp_timer_handle_tperiodic_timer; ESP_ERROR_CHECK(esp_timer_create(&periodic_timer_args, &periodic_timer)); ESP_ERROR_CHECK(esp_timer_start_periodic(periodic_timer,10*1000));// lv_demo_widgets();// lv_demo_music();// lv_demo_benchmark();// avi_player_load...
//初始化TP_SERVICE LOCAL void APP_RegisterRefService(void) { // Register TP event SCI_RegisterMsg(TP_SERVICE, (uint8)TP_DOWN, (uint8)(TP_MSG_MAX - 1), TPCallBackFunc); } //后续的执行都放在回调函数里面进行 LOCAL void TPCallBackFunc(BLOCK_ID id, uint32 argc, void *argv) { #if...
开发板情况汇总esp32 s3 eye主控特性 ESP32-S3-WROOM-1,8 MB Flash + 8 MB PSRAM,和“ESP32-S3-DevKitC-1”同主控 MB-V2.2, camera OV2640SUB-V1.1,1.3” LCD(1.3‘,240X240)接口芯片为ST7789V. [env:esp32-s3-…
32pwm0_sync1_in0nopwm0_out0a1’d1 E 33pwm0_sync2_in0nopwm0_out0b1’d1 S P34pwm0_f0_in0nopwm0_out1a1’d1 3 2 35pwm0_f1_in0nopwm0_out1b1’d1 36pwm0_f2_in0nopwm0_out2a1’d1 37—0nopwm0_out2b1’d1 39pcnt_sig_ch0_in00no—1’d1 (40pcnt_sig_ch1_in00no—1...
ESP_ERROR_CHECK(esp_eth_start(eth_handle)); } } Clock speed is set to 20Mhz, while same shared bus config initialises the sd card as follows: esp_err_t sd_init(void) { esp_err_t ret; // Options for mounting the filesystem. ...
#include "esp_camera.h" #define CAMERA_MODEL_AI_THINKER // Has PSRAM #include "camera_pins.h"//找一个cam的camera_pins.h文件放入目录下 //以下引脚都可以成对配置,根据你的显示屏引脚位置自行选择,注意部分引脚不能混用.320*240 #define TFT_CS 12//2//13//15 ...
fb_count = 1; } // Init Camera esp_err_t err = esp_camera_init(&config); if (err != ESP_OK) { Serial.printf("Camera init failed with error 0x%x", err); return; } Serial.println("Starting SD Card"); delay(500); if (!SD_MMC.begin("/sdcard", true)) { // true enables...
E (1735) app_camera: Camera init failed with error 0x20004 1. 2. 3. 解决: 没有配置引脚导致的,按照上面的配置好引脚就没问题了。 问题2: W (12405) httpd_parse: parse_block: request URI/header too long W (12405) httpd_txrx: httpd_resp_send_err: 431 Request Header Fields Too Large -...
// This function will clip the image block rendering automatically at the TFT boundaries tft.pushImage(x, y, w, h, bitmap); // This might work instead if you adapt the sketch to use the Adafruit_GFX library // tft.drawRGBBitmap(x, y, bitmap, w, h); ...
(ESP_IF_WIFI_STA, &wifi_config)); + ESP_ERROR_CHECK(esp_wifi_connect()); + + cJSON_Delete(root); + + const char *response = "{\"status\":\"success\",\"message\":\"WiFi配置已提交,正在连接...\"}"; + httpd_resp_set_type(req, "application/json"); + httpd_resp_send(req...