本演讲介绍由乐鑫打造的 C语言库:esp-serial-flasher,它主要用于 flash 编程、将应用上传到RAM,或从其他微控制器或单板计算机中获取乐鑫芯片的信息。演讲介绍了利用 esp-serial-flasher 能够构建或优化的产品种类,并分享来自客户的成功案例;同时还通过实际操作演示如何自行使用此库。
SERIAL_FLASHER_RESET_HOLD_TIME_MS This is the time for which the reset pin is asserted when doing a hard reset in milliseconds. Default: 100 SERIAL_FLASHER_BOOT_HOLD_TIME_MS This is the time for which the boot pin is asserted when doing a hard reset in milliseconds. ...
Re: ESP SERIAL FLASHER by ESP_igrr » Thu Oct 06, 2022 12:46 pm pepopi wrote: The part of pressing a push button and transferring the selected firmware, bootloader and partition table should it be included in esp32 example main or in the example commons? This is totally up to yo...
Re: ESP SERIAL FLASHER by ESP_igrr » Thu Oct 06, 2022 12:46 pm pepopi wrote: The part of pressing a push button and transferring the selected firmware, bootloader and partition table should it be included in esp32 example main or in the example commons? This is totally up to yo...
This is an Android application that uses the esp-serial-flasher C library for flashing applications to the RAM of Espressif SoCs. Now it is recommended to use project esptool-android with this application. Installation Install the APK esp-serial-flasher.apk. Screenshots License The MIT License (...
Re: ESP SERIAL FLASHER by ESP_igrr » Thu Oct 06, 2022 12:46 pm pepopi wrote: The part of pressing a push button and transferring the selected firmware, bootloader and partition table should it be included in esp32 example main or in the example commons? This is totally up to yo...
Re: ESP SERIAL FLASHER Quote by username » Wed Sep 04, 2024 3:13 pm Along this concept. I saved my 3 .bin files files files to a SD card on the Master. bootloader.bin partitions.bin firmware.bin Would the correct method be for each file ? esp_loader_flash_start esp_loader...
配置页打开后,找到“Serial flasher config” 节点,注意是顶层节点,不是 Bootloader config 下面那个。把 Flash size 改为你要的大小,比如这里我要 16 MB。 设置好后点击页面顶部的 【保存】 按钮,最后关闭页面。 直接编译项目即可。这里老周是图方便,毕竟用项目来编译 bootloader 可以少很多麻烦。当然,bootloader ...
配置页打开后,找到“Serial flasher config” 节点,注意是顶层节点,不是 Bootloader config 下面那个。把 Flash size 改为你要的大小,比如这里我要 16 MB。 设置好后点击页面顶部的 【保存】 按钮,最后关闭页面。 直接编译项目即可。这里老周是图方便,毕竟用项目来编译 bootloader 可以少很多麻烦。当然,bootloader ...
通过键盘方向键移到“Serial flasher config”回车进入 移动到flash size选项,根据自己更换的flash大小选择8MB或者16MB 然后按s进行保存,弹出的对话框回车确认 按Q键退出设置窗口,回到命令提示符窗口 接下来执行idf.py build编译项目 由于编译实在太长了,我就不在这里重复演示放图了。