9. RESET button 10. BOOT button Press before reset to enter download mode Interfaces Type-C interface: The development board uses the CH343P chip to convert USB to UART, and connects the UART_TXD (GPIO43) and UART_RXD (GPIO44) of ESP32-S3 for firmware flashing and log printing. With...
rst:0x8 (TG1WDT_SYS_RESET),boot:0x13 (SPI_FAST_FLASH_BOOT) configsip: 0, SPIWP:0xee clk_drv:0x00,q_drv:0x00,d_drv:0x00,cs0_drv:0x00,hd_drv:0x00,wp_drv:0x00 mode:DIO, clock div:1 load:0x3fff0030,len:1344 load:0x40078000,len:3964 load:0x40080400,len:3600 entry 0x4008...
1 串口服务器 ESP8266工作在TCP服务器模式时,可以借助IOTGATEWAY很轻松地将传统设备接入物联网,实现多设备实时监控 2 参数配置 串口服务器就像是一个路由器一样,用户可以通过浏览器访问后台来配置模块的相关参数 2.1串口参数 2.2 WiFi参数 esp8266的wifi可以工作在三种模式下,AP模式、STA模式、AP+STA模式,作为串口服...
libusb_reset() is not functional. Libusb prints the error AbortPipe (pipe address 02) failed: [22] The device does not recognize the command and returns with a success code. So, OpenOCD still thinks that the revive_device has been completed successfully. But still, continue to get write...
factory_reset: name: "Factory Reset Radar" restart: name: "Restart Radar" query_params: name: query params #Exposes control switches switch: - platform: ld2410 bluetooth: name: "Radar ControlBlue tooth" id: radar_bluetooth engineering_mode: ...
How did you configure them? You may need to do an gpio_reset_pin() on the GPIO to get them out of JTAG mode. It was just with gpio_set_direction. But gpio_reset_pin solved everything. Thanks a lot! radurotaru19 Posts:4 Joined:Wed Dec 07, 2022 2:09 pm ...
rst:0x1 (POWERON_RESET),boot:0x3 (DOWNLOAD_BOOT(UART0/UART1/SDIO_REI_REO_V2)) waiting for download 烧录完程序,在不掉电的情况下,按en重启,程序可以正常运行,打印的LOG如下: rst:0x1 (POWERON_RESET),boot:0x13 (SPI_FAST_FLASH_BOOT) configsip: 0, SPIWP:0xee clk_drv:0x00,q_drv:0x00...
However, when I attempted to save energy by replacing `delay()` with light sleep at the end of my `loop()`, the ESP32-S3 started rebooting, reporting an RTCWDT_RTC_RESET error. From my research, it seems that the WDT_RTC generates a timeout to prevent the system from sleeping ...
(evt_queue.hid_host_device.handle, evt_queue.hid_host_device.event, evt_queue.hid_host_device.arg); } } } ESP_LOGI(TAG, "HID Driver uninstall"); ESP_ERROR_CHECK(hid_host_uninstall()); gpio_isr_handler_remove(APP_QUIT_PIN); xQueueReset(app_event_queue); vQueueDelete(app_event_...
One issue we are aware of that might be a problem is that the FTDI chip used on The Thing doesn't work very well with Chrome when we reset the device for USB programming. We've nailed it down to either driver issues or most probably something to do with Chrome. We'll need to ...