使用esp_read_mac(uint8_t *mac, esp_mac_type_t type) 函数将首先读取 esp_base_mac_addr_get() 函数获取的 base_mac 的地址 使用esp_efuse_mac_get_default(uint8_t *mac) 函数将获取到 ESP32 设备出厂默认写入 EFUSE BLOCK0 的 MAC 地址。 注: 使用 esp_efuse_mac_get_default(uint8_t *ma...
Repository files navigation README LGPL-2.1 license Arduino core for ESP8266 WiFi chipQuick linksLatest release documentation Current "git version" documentation Install git version (sources)Arduino on ESP8266This project brings support for the ESP8266 chip to the Arduino environment. It lets you writ...
[i].read(); char recv_word = serverClients[i].read(); recv_str_from_client = recv_str_from_client + recv_word; //Serial.write(recv_word); //Serial.write("_"); recv_msg[index2] = recv_word; index2++; } recv_msg[index2] = '\0'; Serial.println("string type print"); ...
不定长写入方式 BluetoothSerial::read() 一样见文生意 读取蓝牙数据的方法 每次读取1字节 蓝牙寄存器采用的先进先出 read()每调用一次 蓝牙数据寄存器的字节就-1 BluetoothSerial::register_callback() 该方法用来登记回调函数 不了解回调函数的请自行百度。 ??? 牛逼,普通蓝牙没有居然是??? 原来如此 有各种网...
uart1 = UART(1, 115200) uart1.any() uart1.write(‘hello world!’) uart1.read(1) 软件SPI 总线¶ 有两个SPI驱动,一个是软件实现的(bit-banging),可以用于任何引脚。 详见machine.SPI: frommachineimportPin,SPI# construct an SPI bus on the given pins# polarity is the idle state of SCK# ...
String macAddress()获取mac地址; 使用演示 数据通讯 使用下面代码进行以太网通讯演示: AI检测代码解析 #include <ETH.h> //引用以使用ETH #include <WiFiUdp.h> #define ETH_ADDR 1 #define ETH_POWER_PIN -1 #define ETH_MDC_PIN 23 #define ETH_MDIO_PIN 18 ...
("Host mac Address:");Serial.println(WiFi.softAPmacAddress());Serial.print("Number of Host Connections:");Serial.println(WiFi.softAPgetStationNum());Serial.print("Host Network ID:");Serial.println(WiFi.softAPNetworkID());Serial.print("Host Status:");Serial.println(WiFi.status());delay(...
defrecv_cb(e):whileTrue:# Read out all messages waiting in the buffermac, msg = e.irecv(0)# Don't wait if no messages leftifmacisNone:returnprint(mac, msg) e.irq(recv_cb) 广播消息的方法: bcast =b'xff'*6e.add_peer(bcast) ...
├── CMakeLists.txt ├── main │ ├── CMakeLists.txt │ └── wifi_tutorial.c # Source file that contains the entry point │ └── tutorial.c # Create this source file │ └── tutorial.h # Create this header file └── README.md 下面,我们需要编辑 main/CMakeLists.txt...
AP+STA的工作原理就是:当模块作为AP时,它同时又可以作为一个STA模式存在,例如:WiFi模块作为AP,可以让客户的手机或者计算机接入,同时该模块又可以作为一个STA接入到路由器或者上位服务器进行数据上传。需要注意的是,模块在AP和模块做STA时的MAC地址是不同的,所以在模块内部看到模块做AP时的MAC地址与在路由器里面去看...