乐鑫(Espressif)的ESP USB Bridge是一个基于ESP-IDF的项目,它可以利用ESP32-S2或ESP32-S3的USB接口,将其用作USB 转UART或USB转JTAG的调试板。 ESP USB Bridge可以替代基于CH340或CP2104的USB转TTL调试板,在JTAG bridge模式下与OpenOCD一起使用,也可以将UF2固件文件烧录到目标板上。
注意,PORT 是指由连接到 ESP32-S2 串口的 USB 转 UART 芯片所创建的串口,不是 ESP32-S2 直接提供的 USB 接口,这个串口只能用于烧录。此后,ESP USB Bridge 即可通过 USB 接口工作。 开发板 原理图中展示了一个将 ESP32-S2 (ESP USB Bridge) 与目标 MCU (ESP32) 相连的简单开发板。项目的默认配置已使用...
ESP USB Bridge (https://github.com/espressif/esp-usb-bridge) 是一个 ESP-IDF (https://github.com/espressif/esp-idf) 项目,能够利用 ESP32-S2 (https://www.espressif.com/zh-hans/products/socs/esp32-s2) 或 ESP32-S3 (https://www.espressif.com.cn/zh-hans/products/socs/esp32-s3) 在计算...
安装ESP prog驱动 官方说明:https://github.com/espressif/esp-iot-solution/blob/master/documents/evaluation_boards/ESP-Prog_guide_cn.md ESP-Prog 采用 FTDI 公司的 FT2232HL 为 USB Bridge Controller 芯片,可通过配置将 USB 2.0 接口转换为支持多种工业标准的串行和并行接口。ESP-Prog 使用 FT2232HL 默认的双...
The USB stack of ESP USB Bridge creates a virtual serial port through which the serial port of the target MCU is accessible. For example, this port can be/dev/ttyACMxorCOMxdepending on the operating system and is different from the PORT used for flashing the ESP USB Bridge. ...
ESP-Prog 硬件原理图,PCB 文件,BOM 等文件参考 乐鑫官网硬件参考设计。 Top side Bottom side 3.2. 功能介绍 3.2.1. USB Bridge 的工作模式 ESP-Prog 采用 FTDI 公司的 FT2232HL 为 USB Bridge Controller 芯片,可通过配置将 USB 2.0 接口转换为支持多种工业标准的串行和并行接口。ESP-Prog 使用 FT2232H...
一、烧录 ESP USB Bridge 项目 1.下载项目 git clone https://github.com/espressif/esp-usb-bridge.git 1. 2.配置项目(可选) 打开一个终端 . export.sh #注意有个点和空格 idf.py menuconfig 1. 2. 在vscode中打开终端可直接输入idf.py menuconfig ...
https://github.com/espressif/esp-usb-bridge https://www.bilibili.com/read/cv16476113/ 也这是说用ESP32S2做一个USB 转 UART /JTAG,可以直接调试ESP32,有串口和JTAG 我下载后使用S2可以编译通过,但是改用S3编译却是各种问题。 不知道哪位友用用S3编译通过的。 也请官方的童鞋给个解决方法呗。
wifi音频模块乐鑫深圳代理商ESP USB Bridge开发板上开发UI,ESP USB Bridge 是一个 ESP-IDF 项目,能够利用 ESP32-S2 或 ESP32-S3 在计算机 (PC) 和目标微控制器 (MCU) 之间建立桥接,从而替代 USB 转 UART /JTAG 桥接芯片(例如 CP210x)。 ESP USB Bridge 创建了一个复合 USB 设备,可以通过 USB 电缆被...
ESP-Prog can easily connect to a PC with the use of only one USB cable. Then, the PC can identify the board's downloading and JTAG interfaces (functions) by their port numbers.Given that the power supply voltage may vary on different user boards, either of the ESP-Prog interfaces can ...