(); // 初始化有LED的IO, pinMode(LED_BUILTIN, OUTPUT); digitalWrite(LED_BUILTIN, HIGH); // 初始化blinker Blinker.begin(auth, ssid, pswd); Blinker.attachData(dataRead); Button1.attach(button1_callback); } void loop() { Blinker.run(); } 更改为: #define BLINKER_WIFI #include ...
Setting the LED_BUILTIN value Recent version of Arduino IDE have a pre-definedLED_BUILDINdefined that can be used as the pin that is connected that boards led. This presents a problem for the ESP-01 and ESP-01S which are both programmed using the Generic ESP8266 setting but which have di...
HTTP请求。监听端口(80) void setup(){ Serial.begin(9600); Serial.println(""); pinMode(LED_BUILTIN, OUTPUT); // 初始化NodeMCU控制板载LED引脚为OUTPUT //通过addAp函数存储 WiFi名称 WiFi密码 wifiMulti.addAP("FAST_153C80", "123456798"); // 将需要连接的一系列WiFi ID和密码输入这里 wifiMulti....
参考地址 六、把ESP-01与DHT11连接 连接方法 七、打开Arduino IDE 编写代码 注意修改 Wi-Fi名和 Wi-Fi密码,如果是本地mqtt服务器的话地址填 127.0.0.1 #include <SimpleDHT.h>#include<ESP8266WiFi.h>#include<PubSubClient.h>intpinDHT11 =2;//GPIO2 of ESP8266constchar* ssid ="XXXXX";//手机Wi-F...
This example code is in the public domain The blue LED on the ESP-01 module is connected to GPIO1 (which is also the TXD pin; so we cannot use Serial.print() at the same time) Note that this sketch uses LED_BUILTIN to find the pin with the internal LED ...
pinMode (13,OUTPUT); //Declare the in-built LED pin as output } 在“我的广告设备回调”功能中,我们打印行将列出发现的BLE设备的名称和其他信息。我们需要发现的BLE设备的硬件ID,以便我们可以将其与所需的设备进行比较。因此,我们使用变量Server_BLE_Address来获取设备的地址,然后将其从BLE地址类型转换为字符...
* 使用Ticker实现LED闪烁,并查询定时器存活状态。 */ #include <Ticker.h> // 使用Ticker库,需要包含头文件 Ticker timer1; // 创建一个定时器对象 void setup() { Serial.begin(9600); // 初始化串口 pinMode(LED_BUILTIN, OUTPUT); // 设置LED引脚为输出引脚 ...
LED_BUILTIN to find the pin with the internal LED */ void setup() { pinMode(LED_BUILTIN, OUTPUT); // Initialize the LED_BUILTIN pin as an output } // the loop function runs over and over again forever void loop() { digitalWrite(LED_BUILTIN, LOW); // Turn the LED on (Note ...
让我们看一个串行通信的示例,其中 ESP32 主站将向 ESP32 从站发送“1”或“0”。然后从设备将接收该数据并控制与其数字引脚连接的 LED。我们将使用 UART2 在两块板之间进行通信。 该项目将需要以下组件。 所需组件 两块ESP32 开发板 1个 5mm LED ...
pinMode(LED_BUILTIN,OUTPUT); }voidloop() { digitalWrite(LED_BUILTIN,LOW); delay(1000); digitalWrite(LED_BUILTIN,HIGH); delay(1000); } 例子二:给D1引脚设置高低电平使灯闪烁 连接电路: voidsetup() { pinMode(D1, OUTPUT);//初始化D1引脚为输出引脚}voidloop() { ...