255.2553.向 BGP 对等体发布下一跳为本地路由器的缺省路由在 R4 上向 BGP 对等体 R1 发布一条下一跳为 R4 自己的缺省路由。[R4]bgp 100[R4-bgp]peer 10.0.14.1 default-route-advertise 4.使用 network 命令在 AS 内通告缺省路由在 R3 的 BGP 进程中直接使用 network 命令通告缺省路由。[R3]bgp 10...
port link-type access port default vlan 10 interface Ethernet0/0/2 port link-type access port default vlan 20 interface Ethernet0/0/3 port link-type trunk port trunk allow-pass vlan 2 to 4094 interface Ethernet0/0/4 port link-type trunk port trunk allow-pass vlan 2 to 4094 06 SW4配置...
[AR1-ospf-1]default-route-advertise always default-route-advertise:命令用来将默认路由通告到普通OSPF区域,如果没有配置always参数,本机路由表中必须有激活的非本OSPF默认路由时才向其他路由器发布默认路由。本例中,本地路由表中没有默认路由,所以需要增加always参数。 # 查看R2与R3上的IP路由表 [AR2]display ...
[Huawei-ospf-1]default-route-advertise 重分发默认路由 1. 2. 3. 4. rip中重分发ospf [Huawei]rip 1 [Huawei-rip-1]import-route ospf 1 1. 2. 七、配置nat R1配置 [Huawei]nat address-group 1 100.1.1.20 100.1.1.20 创建公网地址池 [Huawei]acl 2000 创建标准acl [Huawei-acl-basic-2000]rule ...
default-route-advertise #r10本身没有外界的路由,所以向r10发送一条缺省路由 import-route ospf 1 #重发布 area 0.0.0.4 network 172.16.128.1 0.0.0.0 network 172.16.129.1 0.0.0.0 ip route-static 172.16.128.0 255.255.224.0 NULL0 #把汇总路由指向空接口 ...
default-route-advertise area 0.0.0.0 network 10.1.11.0 0.0.0.255 network 10.1.12.0 0.0.0.255 # ospf 200 router-id 3.3.3.3 area 0.0.0.0 network 12.1.1.0 0.0.0.255 # ip route-static 0.0.0.0 0.0.0.0 12.1.1.2 08 AR2配置 interface GigabitEthernet0/0/0 ...
default-route-advertisetype1 area 0.0.0.0 network 10.1.0.0 0.0.0.3 ] ip route-static 0.0.0.0 0.0.0.0 200.1.1.4 在路由器上充当互联网 我们只需要在 Internet 路由器的每个接口上配置 IP 地址。 ] sysname Internet ] int g0/0/0 ip add 200.1.1.4 255.255.255.248 ] int g0/0/1 ip add 100.1....
default-route-advertise always import-route direct import-route static area 0.0.0.0 network 2.2.2.2 0.0.0.0 network 10.12.12.0 0.0.0.3 network 10.22.22.0 0.0.0.3 同样也要在SW1和SW2上宣告网段,关键代码如下: #SW1 ospf 10 router-id 3.3.3.3 ...
trustset priority add interface GigabitEthernet0/0/add interface GigabitEthernet1/0/#firewall zone untrustset priority add interface GigabitEthernet1/0/#firewall zone dmzset priority add interface GigabitEthernet1/0/#ospf 1 router-id default-route-advertise alwaysimport-route directarea #ip route-...
GigabitEthernet0/0/1ip address 192.168.66.1 255.255.255.252interface GigabitEthernet0/0/3ip address 100.1.1.1 255.255.255.252nat outbound 2000ospf 1 router-id 1.1.1.3default-route-advertisearea 0.0.0.0network 192.168.66.0 0.0.0.255network 192.168.88.0 0.0.0.255ip route...