[mm], Figure GA.3-3; dGe, dGi, dGt are gasket calculation diameters (effective, interim, theoretical) [mm], Figure GA.3-4, Table GA.5-1; dE, dF, dL, dS, dW, dX are average diameters of a part or section (designated by the subscript) [mm], Equations (GA.5-6) to (GA.5-...
NOTE This Part applies to design of vessels before putting into service. It may be used for in service calculation or analysis subject to appropriate adjustment. 购买 正式版SS-EN 13445-3:2021相似标准分析测试百科网标准频道是为分析测试行业提供标准信息检索而建立,方便分析测试行业从业人员查找适用的标准...
欧盟压力容器设计标准 EN 13445: 3的附录 G提出了 一个法兰设计的另一方法 ,该方法与传统的 Taylor2Forge法存在很大的不同 。 首先简要叙述了 法兰密封的基本原理以及该另一方法的计算内容和设计步骤 ,然后对该方法的主要内容进行了分析和讨论。 通过与 Taylor2Forge法的比较 ,说明了 该方法在计算内容和步骤上...
BS EN 13480-3:2024 金属工业管道 第3部分:设计和计算 Metallic industrial piping Part 3: Design and calculation 点击打开全屏PDF预览 点击查看大图 标准号 BS EN 13480-3:2024 2024年 总页数 388页 发布单位 英国标准学会 当前最新 BS EN 13480-3:2024 ...
Metallic industrial piping - Part 3: Design and calculation 被代替 首页 标准 EN 13480-3:2012 标准号 EN 13480-3:2012 2012年 发布单位 欧洲标准化委员会 替代标准 EN 13480-3:2017 当前最新 EN 13480-3:2017/prA5:2021 引用标准 EN 10204:2004EN 12953-3:2002EN 13445-3:2009EN 13480-1:2012EN ...
Part 3 This part of the standard gives the rules to be used for design and calculation under internal and/or external pressure (as applicable), local loads and actions other than pressure. The rules provided are both design by formulae (DBF), design by analysis (DBA) and design by ...
EN 13445中法兰设计另一方法的分析和讨论 秦叔经 (全国化工设备设计技术中心站,上海 200040)摘 要:目前大部分国家压力容器规范中采用的基于Tayl or 2Forge 法的法兰设计方法是一个强度设计方法,而不一定能保证螺栓法兰连接接头的密封性能。欧盟压力容器设计标准E N 13445:3的附录G 提出了一个法兰设计的另一方法,...
Design rules for gasketed circular flange connections-Calculation method for full face gasketed joints 交叉引用:EN 1591-1:2001+A1:2009EN 1092-1EN 13445-3EN 13555CR 13642:1999购买本文件时可获得的所有现行修订均包含在购买本文件中. - 国外-国外国家-英国标准学会 GB-BSI 被引量: 0发表: 2012年 ...
第46卷第 1期 2009年 2月化工设备与管道 PROCESSEQUIPMENT&PIPING Vol1 46No1 1 Feb1 2009 ·压力容器· EN13445中法兰设计另一方法的分析和讨论秦叔经(全国化工设备设计技术中心站,上海 200040 ) 摘要:目前大部分国家压力容器规范中采用的基于 Taylor2 Forge法的法兰设计方法是一个强度设计方法,而不一定能保证...
the first part of the line (except for the Young module, where I have to consider at temperature instead of cold but we have 80 °C so no differences ) but correct yield point - considering that ANSYS will develop the calculation aways considering Von Mises - has to be root(3)*yield/...