在DWC OTG2.0 Controller手册中,有一章节专门介绍了PFC,Packet FIFO Controller。其内部分为共享FIFO(shared FIFO)以及专用FIFO(Dedicated FIFO),并针对dev和host两种模式,并且还要对周期传输数据的FIFO和非周期数据传输的FIFO进行了不同的解读,还是挺复杂的。以下为总结。 复杂的原因无外乎要功耗低、要面积开销小。
Description: USB 2.0 Hi-Speed OTG Controller Subsystem w/AHB Interface Supporting HSIC (config. as Device only or Full Speed only) Name: dwc_usb_2_0_hs_otg_subsystem-ahb Version: 5.00b ECCN: 5E991/NLR STARs: Open and/or Closed STARs myDesignWare: Subscribe for Notifications Product Type:...
DWC_otg_pmu能够在挂起期间检测恢复、远程唤醒、SRP或连接,并在控制器处于休眠状态时唤醒应用程序。 扩展休眠:在扩展休眠(当OTG_EN_PWROPT=3时启用)中,DWC_OTG_wpc_slv、DWC_OTG_power_dn和DWC_oting_pmu模块被电源门控,此功能仅在设备模式下受支持。DWC_otg_piu模块能够检测Resume,并可以通过NAK握手响应IN/...
对应中断状态寄存器GINTSTS,中断是一个分层的结构,即总分的形式,先整体有总的中断状态,比如是设备IN还是OUT端点中断,是主机Port还是通道相关中断,是OTG的中断,还是内核相关的中断。比如如果知道是设别IN或者OUT中断则往下走一层看是DAINT是哪一个IN端点或者哪一个OUT端点的中断,找到了然后再往下走一层查看具体的DIEP...
• CIL:Core Interface Layer•HCD: Host Contoller Driver•PCD: Perpherial Contoller DriverDWC_otg文件列表及功能介绍如下所示:dwc_cfi_common.h[code]This file contains th
DWC3(DesignWare USB 3.0 Controller)和XHCI(eXtensible Host Controller Interface)都是与USB控制器相关的技术,但它们的作用和实现层次有所不同。 1.DWC3(DesignWare USB 3.0 Controller) 芯片级别的USB控制器:DWC3是由Synopsys设计的USB控制器IP,用于集成到SoC(系统级芯片)中。它是一个硬件IP模块,提供了USB 3.0...
[ 1.598530] dwc2 13500000.otg: DWC OTG Controller [ 1.603444] dwc2 13500000.otg: new USB bus registered, assigned bus number 1 [ 1.610775] dwc2 13500000.otg: irq 9, io mem 0x00000000 dwc2就是usb2.0的一个控制器,dw是DesignWare是一个IP核设计公司。
在dwc3中先调用 dwc3_get_dr_mode()取得usb mode(dr_mode),这可以是otg、host或者device 3)然后调用 dwc3_core_init()初始化usb PHY interface和usb PHY,usb PHY的初始化参照第4节。 4)最后调用 dwc3_core_init_mode()初始化usb mode: 如果dr_mode为device,则初始化gadget。 如果dr_mode为host,需要初...
dwc_otg exports usb_gadget_probe_driver function and patches out the udc-core module which normally exports it. This breaks other USB device controller drivers, most notably the virtual dummy_hcd ones, and causes the kernel compile to throw a load of errors if you try to build dwc_otg and...
if (!IS_ENABLED(CONFIG_USB_DWC3_OTG)) { /* * DWC_usb31 and DWC_usb3 v3.30a and higher do not support OTG * mode. If the controller supports DRD but the dr_mode is not * specified or set to OTG, then set the mode to peripheral....