//创建一个OneWire对象 OneWire oneWirePin(temp_sensor); DallasTemperature sensors(&oneWirePin); voidsetup(void) { //激活Arduino串行接口 Serial.begin(9600); //设置LED作为输出 pinMode(redLedPin, OUTPUT); pinMode(greenLedPin, OUTPUT); pinMode(blueLedPin, OUTPUT); sensors.begin();//温度传感...
constintSENSOR_PIN = 6;// Arduino 引脚连接到 18B20 传感器的 DQ 引脚 OneWire oneWire(SENSOR_PIN);// 设置一个 oneWire 实例 DallasTemperature sensors(&oneWire);// 将 oneWire 传递给 DallasTemperature 库 LiquidCrystal_I2C lcd(0x27, 16, 2);// I2C地址0x27,16列2行 floattempCelsius;// 摄氏温...
一、硬件准备Arduino ESP8266/ESP32开发板多路DS18B20温度传感器杜邦线若干面包板电源适配器二、硬件连接将...
void setup() {//pinMode(TempSensor,INPUT);sensors.begin();// set up the LCD's number of columns and rows:lcd.begin(16, 2);// Print a message to the LCD.lcd.print("Current Temp:");} void loop() {// Get 18B20 Datasensors.requestTemperatures();float t = sensors.getTempCByIndex...
Arduino 实例代码 #include <DallasTemperature.h> DallasTemperature tempSensor; void setup(void) { Serial.begin(9600); tempSensor.begin(3); // Connect DS18B20 to Digital Pin 3 } void loop(void) { // Check if the sensor is working correctly ...
Waterproof 1 Wire Digital Temp Sensor Ds18b20 for Arduino, Find Details and Price about Temp Sensor Temp Sensor Ds18b20 from Waterproof 1 Wire Digital Temp Sensor Ds18b20 for Arduino - Focus Sensing and Control Technology Co., Ltd.
Sample Code #include<OneWire.h>intDS18S20_Pin=2;//DS18S20 Signal pin on digital 2//Temperature chip i/oOneWireds(DS18S20_Pin);// on digital pin 2voidsetup(void){Serial.begin(9600);}voidloop(void){floattemperature=getTemp();Serial.println(temperature);delay(100);//just here to slow dow...
将多个DS18B20传感器连接到Arduino 连接非常简单。 首先将所有DS18B20并联连接,即将所有VDD引脚,GND引脚和信号引脚共用。然后将VDD连接至Arduino上的5V输出,将GND连接至Arduino接地,并将信号引脚连接至arduino上的数字引脚2。 接下来,您需要在信号和电源引脚之间的整个总线上增加一个4.7k上拉电阻,以保持数据传输的稳定。(...
PhyphoxBleExperiment Voltmeter;Voltmeter.setTitle("温度测量仪"); // phyphox界面中实验的名称Voltmeter.setCategory("Arduino"); // phyphox界面中实验的分类名称Voltmeter.setDescription("测量温度的仪器");// 创建视图PhyphoxBleExperiment::View firstView;firstView.setLabel("温度随时间的关系图像");// 开始绘制...
序列号。打印(tempF); 序列号。打印(“ \ xC2 \ xB0”);//显示度数符号 序列号。println(“ F”); 由于12位模式下的温度转换最多需要750 ms,因此我在每次测量之间增加了1秒的延迟。 在Arduino上使用多个DS18B20传感器 正如我在简介中提到的那样,您可以仅使用Arduino的一个引脚就可以从多个DS18B20传感器读取温...