下面总结了工作中遇到的Route后DRC、Antenna等问题的几个解决方法。 第一步,不修antenna,降低Timing的优化强度,关掉SI,进行detail route。 setNanoRouteMode -drouteFixAntenna 0 setNanoRouteMode -routeWithTimingDriven 1 setNanoRouteMode -quiet -routeWithSiDriven false routeDesign -globalDetail -viaOpt -wire...
Timing 相关的DRC Max/min Transition time:用于约束信号翻转时上升或下降过程所允许的最大或最小时间,在数字电路实现过程中,该值可以从library 中读出,或用命令set_max_transition, set_min_transition 进行设置。如果两个值同时存在,工具在优化或检查时以最紧的为标杆。 如下例所示,在library 中通常会有default_m...
Full control over IR remote signals: Send any signal (or combination) in any format. Control multiple devices of multiple brands simultaneously. Define your own key combinations of any level of complexity. The only limit is Arduino memory size. Continue reading→ artem Finally, a correct version ...
1、 SVRF---Standard Verification Rule Format(标准的检查文件) 2、 RVE---Results Viewing Environment(显示结果用的环境窗口) 3、 SVDB---Standard Verification Database (LVS results) 4、 DRC---Design Rule Checking 5、 LVS---Layout Versus Schematic 6、 ERC---Electrical Rule Checking 陈远明 第 1...
问用ggplot2和drc绘制剂量响应曲线EN来自近期论文包作者的drc包含了提取参数以供ggplot2使用的说明。它们...
1、 SVRF---Standard Verification Rule Format(标准的检查文件) 2、 RVE---Results Viewing Environment(显示结果用的环境窗口) 3、 SVDB---Standard Verification Database (LVS results) 4、 DRC---Design Rule Checking 5、 LVS---Layout Versus Schematic 6、 ERC---Electrical Rule Checking 实用文档 第...
我们拿到的drc rule中通常会提供一些开关,方便我们按照类型对需要检查的rule进行选择。 但是这种方法并不推荐。因为修改rule的风险在于,你可能忘记修改回来... 而且,如果rule file中没有预定义你所需要的组,或者,你只是想执行某一个rule的检查。那么,修改rule这种方法也并不方便。
2 2|2015-11-05 3 3|2015-11_04 3.1.3 编辑控制文件 test.ctl 编辑控制文件 test.ctl,存放路径为/tmp/test.ctl vi /tmp/test.ctl LOAD DATA INFILE'/tmp/test.txt'INTO TABLEtestFIELDS'|'( C1 TERMINATED BY' ', C2, C3 DATE FORMAT'yyyy-mm-dd') ...
1、 SVRF---Standard Verification Rule Format(标准的检查文件) 2、 RVE---Results Viewing Environment(显示结果用的环境窗口) 3、 SVDB---Standard Verification Database (LVS results) 4、 DRC---Design Rule Checking 5、 LVS---Layout Versus Schematic 6、 ERC---Electrical Rule Checking 陈远明 第 1...
(c) Write to the clock and serial data interface format registers (in manual clock mode only). (d) Write to bit 6 of register 0x05 to enter/exit all-channel shutdown. No other bits of register 0x05 may be altered. After issuing the all-channel shutdown command, no further I2C ...