RAID Level : Primary-1, Secondary-0, RAID Level Qualifier-0可以看出磁盘是的raid级别是raid1, Size是此RAID盘的大小,State: Optimal说明这是正常状态,Number Of Drives : 2这是说有几块盘组成了raid,这里是两块盘租成了raid,Span Depth : 1表示raid的深度,这里就一层,所以综合结果分析这是两块盘做的ra...
dmesg是Linux系统中常用的一个命令,用于显示或控制内核环缓冲区的消息,能够提供关于内核启动和设备驱动程序运行的详细信息。在本篇博客中,我们将详细介绍dmesg命令所有可用的选项,并解释它们的用法和作用。 命令选项 以下是dmesg命令的常用选项: -c:清除内核环缓冲区的内容。 -l:使用指定的日志级别过滤日志消息的显示。
[root@localhost var]# dmesg | grep ttyS* console [tty0] enabledserial8250:ttyS0 at I/O 0x3f8 (irq =4) is a 16550Aserial8250:ttyS1 at I/O 0x2f8 (irq =3) is a 16550A00:0a: ttyS0 at I/O 0x3f8 (irq =4) is a 16550A00:0b: ttyS1 at I/O 0x2f8 (irq =3) is a 1...
[root@localhost ~]# dmesg | grep CPU #查看CPU的信息 Transmeta TransmetaCPU SMP:Allowing 1 CPUs, 0 hotplug CPUs NR_CPUS:32 nr_cpumask_bits:32 nr_cpu_ids:1 nr_node_ids:1 PERCPU:Embedded 14 pages/cpu @c1a00000 s35928 r0 d21416 u2097152 Initializing CPU#0 CPU:Physical Processor ID:0...
# grep CONFIG_LOG_BUF_SHIFT /boot/config-`uname -r` CONFIG_LOG_BUF_SHIFT=18 5. Clear Messages in dmesg Buffer Sometimes you might want to clear the dmesg messages before your next reboot. You can clear the dmesg buffer as shown below. ...
Version 22000.258 WSL Version WSL 2 WSL 1 Kernel Version 5.4.72 Distro Version Ubuntu 20.04 Other Software No response Repro Steps Error occurs when a WSL session is started (i.e. wsl.exe is executed) even if WSL is already running in th...
此时我们只能依据linux记录的错误日志来定位问题。 涉及linux命令 本文涉及以下几条命令 1.dmesg命令,用于获取程序出错时的堆栈地址 1)dmesg|grep -e 'segfault|general' 可以通过该命令过滤出发生崩溃的程序,以及对应的堆栈信息。之前看网上的其他 dmesg最近的输出...
‘dmesg’命令的使用语法如下。1. 列出加载到内核中的所有驱动grep’文字处理工具来处理‘dmesg’命令的输出。由于dmesg日志的输出不适合在一页中完全显示,因此我们使用管道(pipe)将其输出送到more或者less命令单页显示。 root@tecmintcomdmesgmoreroot dmesg命令...
Linux 第05天 1.连接到Internet 1.1 配置网络信息 dmesg命令———查看网卡信息 dmesg | grep -i net ifconfig命令———查看IP、网关等相关信息 ifconfig(可查看活跃的网卡) ifconfig -a (查看所有的网卡) 1.2 配置文件 /etc/sysconfig/network - 如何查看dmesg信息 IP 服务器 重启 转载 网络安全侠 16...
ubuntu系统安装 (考试40分钟)1.做RAID5,并安装ubuntu16.04系统,分区/ 100G,/boot 512MB,data剩余,全部使用XFS文件。2.设置root可以直接远程系统。1. 服务器设置raid,以dell r610 perc6/i阵列卡为例,开机看到提示按ctrl+r键进入阵列卡由于3块硬盘都是新加的,进入主界面是没有配置阵列的按下ctrl+n进入PD mgmt...