1.安装DHT库 由于arduino IDE本身无法直接下载DHT库,在网上寻找第三方库,链接是gitee的,国内能直接访问 DHT.h库 下载为zip包后导入IDE中,具体步骤:项目->管理库->添加.zip库-> 选择下载的zip包 2.使用示例 按照下面图示使用即可 出于某种原因如果无法使用,可以解压下载的zip包,寻找examples\DHT_Test,打开后的代...
硬件连接 DHT11的1脚和4脚分别连接VCC和GND(我连接的是面板包上的USB供电板供电,也可以使用UNO主板上的3.3v、5V和GND接口,为传感器通电即可),2脚连接开发板CPU针脚通信,本例中我连接的CPU引脚也是2号脚,记住你连接的针脚,在后面的编程中需要用到。如下图: 编写读取DHT11温湿度的程序 我们就用DHT库的例程来...
另外,有一点自己在实验的时候遇到的一个小问题,就是我所使用的 UNO R3 Arduino 主板的 DIGITAL 引线排从小到大分别是 RX0 TX1 PIN2 ……,我开始没有认真看清楚,以为 RX0 TX1 之后是 Pin0,我最初设置使用的引脚是 Pin 2,因此我错误的把引线接到 Pin 3上,串口监视器一直没有信息,我以为是传感器坏了,后来...
LiquidCrystal lcd(12, 11, 5, 4, 3, 2); int temp;//温度 int humi;//湿度 int tol;//校对码 int j; unsigned int loopCnt; int chr[40] = {0};//创建数字数组,用来存放40个bit unsigned long time; #define pin 10 //DHT11 连接arduino11引脚 void setup() { Serial.begin(9600); lcd.b...
在多数情况下,测量温度的同时需要测量湿度,本篇博文将介绍使用DHT11温湿度传感器、Arduino Uno和LabVIEW组成温湿度测量系统,可用于粮仓等场合的温湿度监控。 DHT11数字温湿度传感器,是一款含有已校准数字信号输出的温湿度复合传感器,采用专用的数字模块采集技术和温湿度传感技术,具有极高的可靠性与卓越的长期稳定性,内部包...
USB 数据线 × 1 DHT 11 模块 × 1 电路图 代码 // DHT Temperature & Humidity Sensor// Unified Sensor Library Example// Written by Tony DiCola for Adafruit Industries// Released under an MIT license.// REQUIRES the following Arduino libraries:// - DHT Sensor Library: https://github.com/ada...
问Arduino UNO通过DHT11将温湿度数据从I2c发送给Raspberry pi 2(运行windows物联网核)ENRaspberry Pi Pico是具有灵活数字接口的低成本,高性能微控制器板。它集成了Raspberry Pi自己的RP2040微控制器芯片,运行速度高达133 MHz的双核Arm Cortex M0 +处理器,嵌入式264KB SRAM和2MB板载闪存以及26个多功能GPIO引脚。对...
The Arduino microcontroller, being the processing unit of the system, gets the sensor's measured value and compares it with the set threshold. The results are: when the measured room temperature is less than the minimum of the threshold value; then, the microcontroller turns on the heater. If...
with Arduino UNO R3 Kit** The TZT UNO R3 Kit Module Sensor is a comprehensive starter kit designed to introduce beginners to the world of Arduino programming. This kit is not just a collection of components; it's a gateway to unlocking the potential of Arduino UNO R3. With its user-...
在这个项目中,使用 DHT22,检测达到高温时打开风扇,并在达到室温时将其关闭。单片机使用 ARDUINO UNO。 https://hackaday.io/project/186583-shield-dht22hackaday.io/project/186583-shield-dht22 使用NodeMCU ESP8266 创建一个独立的 Web 服务器,通过Arduino IDE编程获取 DHT11 或 DHT22 传感器的温度和湿度...