DHT11 需要来自MCU的启动信号来启动通信。因此,每次 MCU 都需要向 DHT11 Sensor 发送启动信号,要求其发送温度和湿度值。在完成启动信号后,DHT11 会发送一个 包含温度和湿度信息的响应信号。数据通信采用单总线数据通信协议。全数据长度为 40 位,传感器先发送高位数据。 由于上拉电阻,数据线在空闲模式下始终保持在 ...
append(1) #在数据列表后面添加一位新的二进制数据“1” j += 1 print("sensor is working.") print '初始数据高低电平:\n',data #输出初始数据高低电平 print '参数k的列表内容:\n',kk #输出高电平结束后的k值 m = np.logspace(7,0,8,base=2,dtype=int) #logspace()函数用于创建一个于等比数列...
DHT11 传感器接线方法并不复杂,DHT11封装有4个引脚,各个引脚说明如下: 一般从网上买的 Arduino 传感器套件版本的 DHT11,会有一个带 LED 的焊好的板,上面有三个接线引脚,分别是 VCC, GND, DATA,接线时,只要将 VCC 接到 Arduino 5V上,GND 接到 Arduino GND 上,DATA 引脚接 Arduino Pin8上即可。 DHT11 Ar...
const int DHT_PIN = 15; //定义一个整形变量,目的是使用GPIO-15来接收来自传感器的数据 DHTesp dhtSensor; //定义一个DHT传感器 //arduino里的setup函数,执行一次 void setup() { Serial.begin(115200); //串口的速率 dhtSensor.setup(DHT_PIN, DHTesp::DHT11);//把DHT11与gpio第15号数字引脚关联。
4. 5. 6. 7. 8. 9. 10. 11. 12. 代码说明 首先导入Adafruit_DHT库,这是一个用于驱动DHT11传感器的库。 然后通过Adafruit_DHT.DHT11设置传感器类型为DHT11。 接着设置GPIO引脚号,这里设置为4,根据实际连接情况进行修改。 调用Adafruit_DHT.read_retry(sensor, pin)函数读取传感器数据,该函数会自动尝试多次...
import Adafruit_DHT import time # DHT11传感器连接的GPIO引脚和传感器类型 sensor_pin = 4 sensor_type = Adafruit_DHT.DHT11 try: # 读取传感器数据 humidity, temperature = Adafruit_DHT.read_retry(sensor_type, sensor_pin) # 检查是否成功读取数据 if humidity is not None and temperature is not None...
it used special digital module collection technology and humidity sensor technology to ensure product has high reliability and excellent long-term stability. sensors including a resistive feeling wet components and a ntc (temperature measuring el 4、ement, and with a high-performance 8-bit ...
const int DHT_PIN = 15; //定义一个整形变量,目的是使用GPIO-15来接收来自传感器的数据 DHTesp dhtSensor; //定义一个DHT传感器 //arduino里的setup函数,执行一次 void setup() { Serial.begin(115200); //串口的速率 dhtSensor.setup(DHT_PIN, DHTesp::DHT11);//把DHT11与gpio第15号数字引脚关联。
j+=1print("sensor is working.")print'初始数据高低电平:\n',data #输出初始数据高低电平 print'参数k的列表内容:\n',kk #输出高电平结束后的k值 m=np.logspace(7,0,8,base=2,dtype=int)#logspace()函数用于创建一个于等比数列的数组 #即[1286432168421],8位二进制数各位的权值 ...
intchk=DHT11.read(DHT11PIN); Serial.print(“Readsensor:”); switch(chk) { caseDHTLIB_OK: Serial.println(“OK”); break; caseDHTLIB_ERROR_CHECKSUM: Serial.println(“Checksumerror”); break; caseDHTLIB_ERROR_TIMEOUT: Serial.println(“Timeouterror”); ...