[DeviceB]monitor-link group 1[DeviceB-mtlk-group1]port10ge1/0/1uplink[DeviceB-mtlk-group1]port eth-trunk 10 downlink 1[DeviceB-mtlk-group1]quit 在DeviceA和DeviceB上配置DHCPv4中继功能。 # 配置DeviceA。 <HUAWEI>system-view[HUAWEI]sysname DeviceA[DeviceA]interface loopback 0[DeviceA-Loo...
说明:此版本存在一些默认的WLAN无线业务配置,AP上电启动后,默认创建名称为“HUAWEI-XXXX”的SSID,其中XXXX是AP MAC地址的后四位。默认无线业务覆盖使用无认证方式,用户搜索到该SSID之后,无需输入密码就可以成功关联该无线网络。本示例是在其默认配置的基础上提供一些常见配置的修改操作步骤。 业务需求 企业已经部署了有...
uint8_t ret;if(dhcp_state==STATE_DHCP_STOP)returnDHCP_STOPPED;if(getSn_SR(SOCK_DHCP)!=SOCK_UDP)socket(SOCK_DHCP,Sn_MR_UDP,DHCP_CLIENT_PORT,0x00); ret=DHCP_RUNNING; type=parseDHCPMSG();switch(dhcp_state){caseSTATE_DHCP_READY: DHCP_allocated_ip[0]=...
control enable loopback-detection per-vlan enable # interface GigabitEthernet1/0/25 port link-mode bridge shutdown loopback-detection enable # interface GigabitEthernet1/0/26 port link-mode bridge shutdown loopback-detection enable # interface GigabitEthernet1/0/27 port link-mode bridge shutdown ...
# interface GigabitEthernet0/0/1 port link-type trunk undo port trunk allow-pass vlan 1 port trunk allow-pass vlan 100 to 101 # 配置主备WAC Vlanif接口与DHCP服务。 配置主WAC(WAC1)。注意,192.168.101.1已分配给主WAC,192.168.101.1已分配给备WAC,192.168.101.3已分配给VRRP虚地址,需要在主备WAC的...
A DHCP snooping entry includes the MAC and IP addresses of a client, the port that connects to the DHCP client, and the VLAN. The following features need to use DHCP snooping entries: · ARP fast-reply—Uses DHCP snooping entries to reduce ARP broadcast traffic. For more information, see ...
s2(config-if)#dot1x port-control {auto|force-authorized|force-unauthorized}(auto:认证通过后接口状态就变为force-authorized,不通过就为force-unauthorized。force-authorized:强制接口状态为认证通过,这样用户就不需要认证了。force-unauthorized强制接口状态为不通过,这样用户就不能使用接口了) ...
A DHCPv4 client sends messages to a DHCPv4 server through UDP port 68, and a DHCPv4 server sends messages to a DHCPv4 client through UDP port 67. The following table describes DHCPv4 message types. Table 8-25 DHCPv4 message types Message Name Description DHCPDISCOVER A DHCPDISCOVER ...
The interfaces supporting this command include Layer 2 GE interfaces, Layer 2 Ethernet interfaces, Layer 2 Eth-Trunk interfaces, Layer 2 port group, Layer 3 GE interfaces, and Layer 3 Ethernet interfaces. Prerequisites DHCP has been enabled globally by using the dhcp enable command. Follow-up ...
[ 35.991333] r8169 0000:01:00.0 eth4: Link is Up - 1Gbps/Full - flow control rx/tx [ 35.991367] br-lan: port 4(eth4) entered blocking state [ 35.991374] br-lan: port 4(eth4) entered forwarding state [ 35.991519] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready [ 36....