对于基于Red Hat的系统,你可能需要启用额外的软件仓库,如EPEL(Extra Packages for Enterprise Linux)。可以通过以下命令安装EPEL仓库: bash sudo yum install epel-release sudo yum update 然后再次尝试搜索和安装dfu-util。 尝试安装dfu-util软件包: 在添加了正确的软件源并更新了软件包列表后,再次尝试安装dfu-util...
驱动:需要安装dfu 驱动, 可以通过 zading, 安装通用的驱动。 dfu-util 交叉编译 dfu-util 是USB 论坛的 DFU 1.0 和DFU 1.1规范的主机端实现 。DFU 旨在向/从通过 USB 连接的设备下载和上传固件。它的范围从微控制器板等小型设备到手机 本文主要介绍windows 上的交叉编译,Linux 平台交叉编译,直接参考官网即可,...
驱动:需要安装dfu 驱动, 可以通过 zading, 安装通用的驱动。 dfu-util 交叉编译 dfu-util 是USB 论坛的 DFU 1.0 和DFU 1.1规范的主机端实现 。DFU 旨在向/从通过 USB 连接的设备下载和上传固件。它的范围从微控制器板等小型设备到手机 本文主要介绍windows 上的交叉编译,Linux 平台交叉编译,直接参考官网即可,...
dfu-util -a 0 --dfuse-address 0x08004000 -D your-lib.bin dfu-util -a 0 --dfuse-address 0x0800C000 -D your-app.bin How to build dfu-util from source See thebuild instructionsat the dfu-util home page. Links Original forum posts and discussion: Linux procedure Mac OS X spe...
Hi, Using Windows 10 x64 is fine, but using Xubuntu 18.10 x64, I have this error: (using generic_boot20_pc13_fastboot.bin) /home/userz/Arduino/hardware/Arduino_STM32/tools/linux/maple_upload: line 29: /home/userz/Arduino/hardware/Arduino...
dfu-util -a 0 --dfuse-address 0x0800C000 -D your-app.bin How to build dfu-util from source See the build instructions at the dfu-util home page. Links Original forum posts and discussion: Linux procedure Mac OS X specific instructions ...
dfu-util -a 0 --dfuse-address 0x0800C000 -D your-app.bin How to build dfu-util from source See the build instructions at the dfu-util home page. Links Original forum posts and discussion: Linux procedure Mac OS X specific instructions ...
需要使用 Type-C USB 连接器将 EVM 上的端口 J13连接到 Linux 主机。 此外、连接电源并使用 EVM 打开 UART 控制台。 此常见问题解答介绍了使用 DFU 刷写 eMMC 的分步过程: https://e2e.ti.com/support/processors-group/processors/f/processors-forum/1127618/faq-sk...
PyDFUUtilprimarily tested on Linux and Windows, but also can work on each platform wherePyUsblibrary are available, including MacOS Installing PyDFUUtilis generally installed through pip # the latest official release python -m pip install pydfuutil # install a specific version (e.g. 0.0.1b1) ...
Could you try below from Linux PC to transfer binaries to eMMC via DFU?sudo dfu-util -c 1 -i 0 -a 2 -D tiboot3.binsudo dfu-util -c 1 -i 0 -a 3 -D tispl.binsudo dfu-util -c 1 -i 0 -a 4 -D u-boot.imgsudo dfu-util -c 1 -i 0 -a 6 -D...