dfu-util下载 https://github.com/Stefan-Schmidt/dfu-util https://dfu-util.sourceforge.net/dfu-util.1.html https://sourceforge.net/projects/dfu-util/files/latest/download 下载 分类: 单片机 好文要顶 关注我 收藏该文 微信分享 lydstory 粉丝- 37 关注- 0 +加关注 0 0 升级成为会员 ...
-a, —alt 对于单片机,这项带上参数 0 就行了。 -D, —download 要烧录的 dfu 固件。 使用dfu-util 烧写 bin 文件 固件不像固件一样包含地址信息,因此需要指定烧写地址。 通过指定烧写地址,注意 s 是小写,例: 使用dfu-util 读出单片机里的固件 这个功能 Sugar 基本不用,这里只把示例简单写一下。 通过参...
Dfu-util is a host side implementation of the DFU 1.0 and DFU 1.1 [1] specification of the USB forum. Note: This patched sources has quirks for STM32F4xx Black Pill dev.board. DFU is intended to download and upload firmware to devices connected over USB. It ranges from small devices li...
You will need dfu-util 0.5 or newer to download dfu files to theDSO Nano. Older dfu-util versions will not work. The DSO Nano, and many other devices based on ST Micro's microcontrollers, uses ST Micro's own DFU extensions (DfuSe) which are not compatible with the DFU standard. You ...
So to download a raw binary file to a DfuSe device you have to know the target address. Example, to download a raw binary file (in case you are developing): dfu-util -a 0 --dfuse-address 0x08004000 -D your-lib.bin dfu-util -a 0 --dfuse-address 0x0800C000 -D your-app.bin ...
dfu-util: More than one DFU capable USB device found! Try `--list' and specify the serial number or disconnect all but one device 6. I try to download the new image in the newly appeared slot: ~/zephyr/counter/build/zephyr# dfu-util --download zephyr.signed.hex --alt 1 ...
dfu-util is a program that implements the host (PC) side of the USB DFU 1.0 and 1.1 (Universal Serial Bus Device Firmware Upgrade) protocol. DFU is intended to download and upload firmware to devices connected over USB. It ranges from small devices like micro-controller boards up to mobile...
Using dfu-util you can download firmware to your DFU-enabled device or upload firmware from it. dfu-util has been tested with the Openmoko Neo1973 and Freerunner and many other devices." LICENSE="GPL-2.0-or-later" LICENSE_SPDX="SPDX-License-Identifier: GPL-2.0-or-later" LICENSE_URI="...
2. dfu-util -d 03fd:0300 -D ./system.dtb -a 1 8. 在 U-Boot 上看到 DOWNLOAD 消息后,请在 U-Boot 控制台上使用 Ctrl+C 停止 dfu_ram。 ##DOWNLOAD ... OK 按Ctrl+C 退出。 10. 验证在目标器件上是否已成功加载 Linux。 主机侧日志 ...
E:\TI_AM62X\DFU_flash\dfu-util\dfu-util.exe -R -a 1 -D u-boot.img 能正常启动dfu uboot了。然后进行下一个命令。 setenv dfu_alt_info ${dfu_alt_info_emmc} dfu 0 mmc 0 在这里之后,理论上就可以进行下一步的烧录flash命令至eMMC 。