const uint32_t LPI2C4_BAUDRATE = 100000; const uint8_t i2c4_ext_address = 0x25; size_t txCount = 0xFF; status_t reVal = kStatus_Fail; uint8_t i2cExtAddrArray[5] = { 0x33, 0x44, 0xAA, 0xFF, 0x01 }; lpi2c_master_config_t masterExtConfig; LPI2C_MasterGetDefaultConfi...
The MC56F8006 is a processor, if you set the I2C of MC56F8006 as slave IIC module, the slave address of IIC module is programmable, the IIC address register1 is the slave address. In 7 bits slave address mode, the I2C ADDR register is the slave address: If you use 10...
The IRPS5401MTRPBF is an unprogrammed part, there is no default output configuration. ADDR pin for I2C and/or PMBus offset, use a resistor on this pin to set the I2C and/or PMBus address offset for the device. Kindly refer datasheet page number 4 & 5 for pre-defined configurat...
write_fifo_dout_addr->flags = RTIO_SQE_TRANSACTION; rtio_sqe_prep_read(read_fifo_dout_reg, iodev, RTIO_PRIO_NORM, read_buf, buf_avail, lsm6dsv16x->streaming_sqe); Additional contextA similar fix was already applied to i2c_rtio_default: #79890....
i2c_pins.png D3 = SCL = yellow wire D2 = SDA = blue wire You do not have the required permissions to view the files attached to this post. Top DavinRonin Posts: 14 Joined: Tue Oct 22, 2024 12:12 pm Re: Can't find seesaw on default address Post by DavinRonin » Wed Oct...
6 7 CONFIG_SPL_I2C_SUPPORT=y 7 8 CONFIG_SPL_SERIAL_SUPPORT=y configs/theadorable_defconfig +1 Original file line numberDiff line numberDiff line change @@ -2,6 +2,7 @@ CONFIG_ARM=y 2 2 CONFIG_ARCH_MVEBU=y 3 3 CONFIG_SPL_LIBCOMMON_SUPPORT=y 4 4 CONFIG_SPL_LIBGENERIC...
[ 1.978267] imx-i2c 2040000.i2c: can't get pinctrl, bus recovery not supported [ 1.985555] i2c i2c-2: IMX I2C adapter registered [ 1.990528] mc: Linux media interface: v0.10 [ 1.994801] videodev: Linux video capture interface: v2.00 [ 2.000312] pps_core: LinuxPPS API ver. 1 ...
ipaddr=192.168.1.188 IP=192.168.1.188:192.168.1.124:192.168.1.1:255.255.255.0::eth0:off ip=192.168.1.188:192.168.1.124:192.168.1.1:255.255.255.0::eth0:off stdin=serial stdout=serial stderr=serial autostart=yes videostd=pal ver=U-Boot 1.2.0 (May 11 2011 - 11:22:33) ...
ipaddr=192.168.1.188 IP=192.168.1.188:192.168.1.124:192.168.1.1:255.255.255.0::eth0:off ip=192.168.1.188:192.168.1.124:192.168.1.1:255.255.255.0::eth0:off stdin=serial stdout=serial stderr=serial autostart=yes videostd=pal ver=U-Boot 1.2.0 (May 11 2011 - 11:22:33) ...
i2c i2c-0: using dma0chan16 (tx) and dma0chan17 (rx) for DMA transfers pps_core: LinuxPPS API ver. 1 registered pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it> PTP clock support registered bman-fbpr addr 0xfe000000 size 0x1000000 Bman err ...