DD-WRT is a Linux based alternative OpenSource firmware suitable for a great variety of WLAN routers and embedded systems. The main emphasis lies on providing the easiest possible handling while at the same time supporting a great number of functionalities within the framework of the respective hard...
即PATH=$PATH:/home/db90h/toolchains/4.1.0-uclibc/bin2. 到 DD-WRT/opt 目录运行 ./install.sh. 运行 ./install_* 建立一个特定 你要求重建共享代码的第一个变量。 这两个脚本应保存到ready_ddwrt.sh和ready_ddwrt_root.sh。你可以下载他们[[4]]但是ready_ddwrt.sh缺少最后两节,建立write4和webcomp...
https://svn.dd-wrt.com/changeset/52025 this should fix boot problems on ipq based devices with bad nand blocks https://svn.dd-wrt.com/changeset/52026 fix blocksize https://svn.dd-wrt.com/changeset/52027 use correct function https://svn.dd-wrt.com/changeset/52028 use correct function...
下面是可以安装到DD-WRT设备上的附加软件。 注意,你可以用 ipkg 安装OpenWRT 的任意软件包 。Additionally more than 1000 packages are provided with NSLU2-Linux Optware packages build specially for DD-WRT. BWlog -- Bandwidth Log - realtime bandwidth graphing. iftop -- for ncurses-based monitoring ...
wgethttp://downloads.openwrt.org/attitude_adjustment/12.09/ar71xx/generic/packages/libc_0.9.33.2-1_ar71xx.ipkipkginstalllibc_0.9.33.2-1_ar71xx.ipkwgethttp://downloads.openwrt.org/attitude_adjustment/12.09/ar71xx/generic/packages/opkg_618-3_ar71xx.ipkipkginstallopkg_618-3_ar71xx.ipk ...
Use ONLY ext2/3 for partition/drives that you plan for permanent connection to your DD-WRT box,orfor drives where you plan to install additional software packages onto (like optware, Samba, Torrent etc.). You can use any of the three mount points: /opt, /mnt, /jffs ...
通常,DD-WRT映像会占据约26MB分区,即便闪存是128MB或更多,也是如此。可以在未使用的空间创建另一个分区并用其来存储文件。这应该主要是读存储(read-storage),比如无线热点splash和配置页、WEB页、额外的配置文件以及面向ipkg(针对嵌入式设备的ItsyPackage Management System)的存储空间。不要将它用于像日志文件这样能...
要為路由器安裝第三方韌體,首先需要選擇一個合適的韌體,現在最出名的路由器第三方韌體分別是 DD-WRT, OpenWRT 及 Tomato,如果是新手使用,建議先試用 DD-WRT, 因為 DD-WRT 的使用比較 user friendyly。 下一步是要確定該韌體是否支援你的舊有或打算新買的路由器,可以從以下網頁分別查看 DD-WRT 及 OpenWRT 支...
opkg install libc_0.9.33.2-1_ar71xx.ipk Type the following lines to create the configuration file for opkg: cat > /etc/opkg.conf<< EOFsrc/gz snapshots http://downloads.openwrt.org/snapshots/trunk/ar71xx/packagesdest root /optdest ram /opt/tmplists_dir ext /opt/tmp/var/opkg-listsEOF...
Due to the very nature of DD-WRT, its infrastructure, and the routers they support, one must use a Linux file format in order to take full advantage of the thousands of installable packages that allow for incredible user control and add excellent flexibility to the router. ...