applicable Position Control Units, as shown below. The unit version of the Position Control Units begins at version 2.0. Confirming Unit Versions with Support Software CX-Programmer version 4.0 or higher can be used to confirm the unit version using the Unit Manufacturing information command. 1,...
欧姆龙,OMRON,CX-Position操作手册(英文) H7CX-A11-G-NH7CX-AWSD DC12-24CX-PROFI-V1H7CX-AWSD1 AC24/DCH5CX-AD-NH7CX-A4SD-NH7CX-A4WH7CX-AD DC12-24H7CX-A-G-NH7CX-ASD-G DC12-24H5CX-L8D-G-NH5CX-L8DH7CX-R11D1-N-301H5CX-L8ED-NH7CX-A4WSDH5CX-AD AC24/DC12-24H7CX-ASD-NH7C...
25、 Patient Name),6 (by Control Name),7 (by Queue position),8 (by Doctor Name)重叫结果。3.或选9 (Patient Multi-Sample Report),输入Sample ID 后,可选择1 (by Sample ID),2 (by Date),3 (All Reports)重叫出同一 病人的多次检体测试报告。4.重叫出的结果,可选择屏幕显示、打印或传送至计...
样本名称(中文) 下载 CS1W-NC233选型样本 下载[2.99MB] Catalog Name (English) Download CS1W-NC233选型样本 下载[2.45MB] Manual Name (English) Download CS1W-NC233 操作手册 下载[5.15MB] CXONE-AL__D-V4 CX-Position Ver.2.5 Operation Manual 下载[1.73MB] CS1W-NC233 安全注意事项 下载[0.26MB]Ling...
EG2001X_CX 操作手册
Name),7 (by Queue position),8 (by Doctor Name)重叫结果。 3.或选9 (Patient Multi-Sample Report),输入Sample ID后, 可选择1 (by Sample ID),2 (by Date),3 (All Reports)重叫出同一 病人的多次检体测试报告。 4.重叫出的结果,可选择屏幕显示、打印或传送至计算机。 5-2.2吸光值与时间的反应...
Error: Too many parameters found at '^' position. 输入参数太多 Error: Ambiguous command found at '^' position. 输入命令不明确 使用undo命令行 在命令前加undo关键字,即为undo命令行。undo命令行一般用来恢复缺省情况、禁用某个功能或者删除某项配置。几乎每条配置命令都有对应的undo命令行。
Entry of Rung CommentMove the cursor to this position. (The rung is inverted in blue.)ENTThe entry screen shows up.Process_at_Startup Enter a r 37、ung comment.ENT/5-5. Entry of Normally Closed ContactPress “/” from a keyboard to show the New Closed Contact dialog.Creating a ...
•Ignitioncoil•Crankshaftpositionsensor •Camshaftpositionsensor•Distributor •Sparkplugs EMISSIONCONTROLWARRANTY–36MONTHSOR4,000HOURSFORPOWERTRAINPARTS •Intakemanifold •Exhaustmanifold EMISSIONCONTROLWARRANTY–60MONTHSOR3,500HOURSFORGENERALPARTS ...
position. 84 14.COORDINATEMEASUREMENT •Ifnotmeasuredorthespaceisleftblank“Null”willbedisplayed. IfstationpointZcoordinateissetto“Null”theobservationresultfortheZ coordinateisautomaticallysetto“Null”. PROCEDURE 1.Sightthetargetatthetargetpoint. 2.InthethirdpageofOBSmode screen,press[MENU],thenselect...