或者,端口阻抗需要和默认的参考阻抗(Reference Impedance)一致,才能和实测值作比较。 比如说,如果用离散端口做single-ended仿真,端口阻抗应该设置为50欧姆。如果做differential mode仿真,端口阻抗应该为100欧姆。如果做common mode仿真,端口阻抗应该为25欧姆。 謝謝EDATOP大 看看先,谢谢了。资料不错 multimode的下的阻抗...
The input capacitor Ci selection In the typical application, an input capacitor (Ci) is required to allow the amplifier to bias the input signal to the proper dc level for optimum operation. In this case, Ci and the input impedance of the amplifier (Zi) form a high-pass filter with the ...
19、eneralName:Orientation:Text size:Positive 0 Negative largeHelpPosltimCoardnatK: Q Free Q Full 曲 neUse pd特Xrrtn:Virin;-4-0,0-quXmaw:Ymax:Free rarmal positionReference plane Detanze to ref, plne:Nunber of modes:rl Polarization angleMode settlriosriMdipri portDsflreI-! Impedance and...
在CST搭建模型时,如何设置端口和2 V的电源激励呢? 关于端口是用discrete port 还是wave guide port. 个人认为应选用discrete port 里面的 impedance port ,值为50欧姆,这样可以对应PCB模型中的50欧姆的电源阻抗和负载阻抗。 如果是这样,又如何加入2V的电源激励呢, 因为CST里面电源的默认值都是1V啊。 初学,有些...
Impedance element (S-Parameter type):该端口通过集中元件包括含内阻的激励和吸收功率的电流源来模拟仿真。在瞬态分析中,只有离散单元是激励端口时,电流源才被激活。该端口提供1w的输入功率并可计算基于入射和反射时间信号相应的S参数。另外,也可以监控横过离散端口的电压和穿过离散端口的电流。注意,离散端口的方向用来...
♦ Sink Current Capability 1 mA to 100mA ♦ Low dynamic output impedance, 0.2W typ. ♦ 0.5%, 1% or 2% reference voltage tolerance ♦ Alternate for TL431, TL431, LM431 & AS431 ♦ Temperature range 0°C to+ 70 °C ♦ Available in SOT-23, TO-92, SOT-89 and SOP- 8 packa...
CST中的激励源
因为输入和输出阻抗必须是50 欧姆,我们要改变‘Fixed Impedance’属性,把它设置为默认的50欧姆。 CST DESIGN STUDIO™ 2006 – Getting Started Tutorials 19 这部分将向你演示如何获得你感 的结果。 解释全局设定,并设置 “simulation task” 。 设定 现在,我们已经赋值给元件,这些值的 都是全局 。如果你把 从...
The GM1431 is an ideal voltage reference for 3.0 to 3.3V switching power supplies. Features♦ Sink Current Capability 1 mA to 100mA♦ Low dynamic output impedance, 0.2W typ.♦ 0.5%, 1% or 2% reference voltage tolerance♦ Alternate for TL431, TL431, LM431 & AS431♦ Temperature ...
Output Impedance(HS+LS)RONIo=±200mA—0.260.6Ω Protection Circuits Thermal shutdown temperatureTTSDDie temperature—150—℃ CST2466/CT2466EINPUT AND OUTPUT TRUTH TABLE InputOutputFunction INAINBOUTAOUTB LLHi-ZHi-ZStand-by(Stop) HLHLA CH output ...