把里面的“CPU Loadline Calibration Control”改为“Mode 4”,防止低负载下过度欠压导致异常关机 这个东西简称“LCC”,是用来调整CPU负载补偿的,每个模式的差异如下图所示,对于一般人而言,“Mode 3”到“Mode 6”是比较适合的参数。虽然视处理器个体体质不同,但建议“Curve Optimizer”的负压值给的越大,“LCC”...
对于MSI[微星]: 方案A):在BIOS中,选择“OC”,选择“CPU核心电压模式”,选择“Offset Mode”,选择“+(By PWM)”,调整电压直至系统稳定,建议不要超过0.025V为单次增加。 方案B):在BIOS中,选择“OC”,选择“DigitALL Power”,更改“CPU Loadline Calibration Control”,建议从“Mode 7”开始到较低的值,直到系...
CPU防掉压设置,在DigitALL Power选项里面,我将CPU Loadline Calibration Control设置为Mode4,设置放掉压的目的是在高负载下防止CPU掉压过大。 最后,为了避免机箱内部积热,将机箱风扇转速调高一点。如果机箱风扇只有1200RPM~1500RPM建议直接拉满,在Easy Mode里面的Fan Info中设置: 测试过程中不要忘记反复烤机,得益16相...
MSI MAG B760M MORTAR MAX WIFI GLOWAY DDR5 6400C32 16G*2 进bios-OC Overclocking: >Advanced CPU Configuration---CPU lite loadcontrol→高级 ---AC Loadline →50 >DigitALL Power---CPU Loadline Calibration Control→mode8→mode7 //(7.29鲁大师CPU测试蓝屏clock_watchdog_timeout >CPU Core Voltage Mo...
3、CPU Load line calibration control选mode5,这是设置防掉压 4、CPU lite load control选高级,然后CPU AC Loadline改成1,CPU DC loadline改成80。 5、CPU核心电压模式选Adaptive+offset mode+VF point,CPU Core电压选自动,CPU core offset -0.08,底下的VF point根据你cpu的体制,在5.1以上的频率在offset -0.01...
CPU Loadline Calibration set to “Auto” (Mode 3). BIOS will apply the optimized setting when you’re overclocking. If you would like to know more about this topic, visit the link provided here for more details:LLC, WHAT IS IT AND WHY ARE MSI Z370 MOTHERBOARDS THE BEST CHOICE FOR ...
CPU Loadline Calibration set to “Auto” (Mode 3). BIOS will apply the optimized setting when you’re overclocking. If you would like to know more about this topic, visit the link provided here for more details:LLC, WHAT IS IT AND WHY ARE MSI Z370 MOTHERBOARDS THE BEST CHOICE FOR ...
將CPU Lite Load Control改為Intel Default 重新啟動電腦 方案B: 進入BIOS 選擇超頻>CPU Core Voltage Mode>Offset Mode 調節+(By PWM)直到系統穩定(每次增加不要超過0.025V) 重新啟動電腦 方案C: 進入BIOS 選擇超頻>DigitALL Power 變更CPU Loadline Calibration Control從Mode 7開始並繼續降低,直到系統穩定 ...
In BIOS, select "OC," select "DigitALL Power," change "CPU Loadline Calibration Control," . We recommend starting from "Mode 7" to a lower value until the system is stable. Note: After trying out 1 or 2, run the XTU test again and see if the AVX2 te...
▶ CPU NB Loadline Calibration Control CPU-NB 电压会根据 CPU-NB 的负载呈比例性递减.本项目重载线校准越高时,将可 提高电压值与超频能力,但也会增加温度.如果设置为 Auto,BIOS 将自动配置此设置. 38 BIOS 设置 ▶ CPU NB Over Current Protection 设置 CPU-NB 过高电流保护极限值.如果设置为 Auto,...