第四步:配置调试文件 在这里我们要设置下调试的launch文件 选择我们的cortex-debug 在launch那写代码,我这里是stlink和openocd所以可能有些不一样, {"cwd":"${workspaceRoot}","executable":"${workspaceRoot}/Output/Debug/template.axf",//可执行文件的路径,你看你自己的是在哪"name":"stlink",//用的什...
较常用的是JLink GDBServer和OpenOCD,前者只支持 JLink 调试器,后者支持 jlink,stlink,cmsis-dap,等众多调试器 JLink GDBServer 位置于官方的 JLink 驱动程序中,OpenOCD 需要自行去下载 下面是一个示范,每个人的安装位置可能有所不同: 注:下图配置了 JLinkGDBServer 和 OpenOCD,因为本文章要使用 两种不同的调试...
较常用的是 JLink GDBServer 和 OpenOCD,前者只支持 JLink 调试器,后者支持 jlink,stlink,cmsis-dap,等众多调试器 JLink GDBServer 位置于官方的 JLink 驱动程序中,OpenOCD 需要自行去下载 下面是一个示范,每个人的安装位置可能有所不同: 注:下图配置了 JLinkGDBServer 和 OpenOCD,因为本文章要使用 两种不同的...
2、调试烧录launch.json配置 在rtthread studio的调试配置下载这里,有用到了外部flash烧录算法,路径也做了说明,如此一来也可以方便进行拷贝。 在launch.json中,大部分都是走的openocd,但这种烧录调试性能往往比不上st自己的gdb server,加之也不用配置那么多cfg文件,只需要告知device型号即可。 对于flm算法加载,使用-...
SERVER CONSOLE DEBUG: onBackendConnect: gdb-server session connected Open On-Chip Debugger 0.11.0 Licensed under GNU GPL v2 For bug reports, read http://openocd.org/doc/doxygen/bugs.html WARNING: interface/stlink-v2.cfg is deprecated, please switch to interface/stlink.cfg embedded:startup....
Only works with OpenOCD, JLink, and STLink, currently. How it works internally for OpenOCD Configure OpenOCD to accept multiple GDB connections. This part is very fragile and must be done before init. This part is customizable, and if the default mechanism doesn't work, you need to be...
Are you confused by all the buzzwords used around embedded debugging (i.e SWD vs JTAG, OpenOCD vs pyOCD vs JLinkGDBServer, CMSIS-DAP vs ST-Link vs J-Link, etc) I’ve run into all of these issues! Having a basic understanding of the technology stack in use can be helpful for ...
本例中展示的是 OpenOCD 使用 STLink 调试 STM32F103 的配置,其他类型的配置和这差不了太多 PyOCD 基本配置如下: 属性解释: targetId:芯片的系列名称 如果你安装了 CMSIS 包,并选择了芯片类型,你可以在视图中看到此名称: cmsisPack:CMSIS 包的绝对路径 ...
STM8-Debug是一个 Vscode 上的STM8调试器,通过使用GDB连接 STLink 设备完成对 STM8的调试1. vscode:launch.json配置2. F5 启动调试注意事项:launch.json的executable 字段必须是含有gdb调试信息的可执行文件路径,IAR 或者 COSMIC 生成的都可以 此版本GDB不支持任何中文路径 ...
The OpenOCD ITM support is limited to using the ST-LINKv2 hardware interface to the target board. For example, as built-in to the STM32F4DISCOVERY and STM32x0G-EVAL platforms. The ST-LINKv2 firmware on the boards should be at leastJTAG v17, so older boards may need to have their ...