配置peer connect-interface命令后,会引起邻居会话断开连接,然后再重新建立连接。 因为一台设备上各地址族下的BGP共用一条TCP连接,所以在BGP视图下配置的connect-interface信息能在IPv4单播地址族下被继承。 为了使物理接口在出现问题时,设备仍能发送BGP报文,可将发送BGP报文的源接口配置成Loopback接口。在使
peer 1.1.1.1 connect-interface LoopBack0 peer 4.4.4.4 as-number 200 peer 4.4.4.4 ebgp-max-hop 255 两个EBGP通过环回口建立,需要指定EBGP多跳 peer 4.4.4.4 connect-interface LoopBack0 # ipv4-family unicast undo synchronization peer 1.1.1.1 enable peer 1.1.1.1 next-hop-local //AR2将AR4上的路...
Peer 2.2.2.2设备配置如下所示。as-number 300 Peer 1.1.1.1 ebgp-max-hop 2 Peer 1.1.1.1 connect-interface LoopBack0 peer 2.2.2.2 ebgp-max-hop 2 Peer 2.2.2.2 connect-interface LoopBack0 RTB: Bgp 200 Network 10.252.1.1 255.0 Undo snchronization ...
[ -bgp]peer (另一个AS的EBGP的回环口IP地址) as-number (ebgp邻居所属的AS编程) [ -bgp]peer (另一个AS的EBGP的回环口IP地址) connect-interface LoopBack0(配置的回环口) [ -bgp]peer (另一个AS的EBGP的回环口IP地址) ebgp-max-hop (最大跳数) ebgp报文允许的最大跳数最小应改为2(默认为1),...
The loopback interface of the device's BGP peer must be reachable. In the case of an EBGP connection, thepeer ebgp-max-hopcommand needs to be run to enable the two devices to establish an indirect peer relationship. When loopback interfaces are used to establish a BGP connection, you are...
bgp邻居停留在connect状态两个路由器建立ibgp邻居建立不起来，状态停留在connect的状态，使用loopback地址...
interface Loopback100vrf forwarding 10ip address 192.168.7.7 255.255.255.255!interface Loopback65528vrf forwarding 65528ip address 192.168.1.1 255.255.255.255!interface Tunnel1ip unnumbered GigabitEthernet1no ip redirectsipv6 unnumbered GigabitEthernet1no ipv6 red...
interface GigabitEthernet1.1352 no shutdown encapsulation dot1Q 1352 ip address 198.18.0.5 255.255.255.252 no ip redirects ip mtu 1496 exit interface Loopback100 no shutdown vrf forwarding 10 ip address 192.168.7.7 255.255.255.255 exit interface Tunnel1 ...
NoteUse of this sample requires network access using the loopback interface. Prerequisites The following examples use JavaScript. For help creating your first app, seeCreate your first Windows Store app using JavaScript. To ensure your Windows Store app is network ready, you must set the capability...
interface Loopback0 ip address 10.210.0.1 255.255.255.255 ! interface Tunnel0 ip vrf forwarding Prod ip address 169.254.231.1 255.255.255.248 tunnel source 10.210.0.1 tunnel destination 10.200.0.0 ! interface Tunnel1 ip vrf forwarding NonProd ...