在Packet Tracer中，当你在Router(config)#模式下配置IP地址时，这属于全局配置模式。这种模式下，你无法直接为设备配置IP地址，因为这是模拟环境的设定，真实的设备上是不允许在全局配置模式下进行IP地址配置的。而当你进入Router(config-if)#模式，这意味着你已经进入了接口配置模式。在这一模式下，你...
1、开启密码生效Router(config-line)。2、配置特权模式密码Router(config。3、创建本地用户benet和密码ciscoRouter即可。思科config_isakmp用户模式。以终端或Telnet方式进入路由器时系统会提示用户输入口令,输入口令后便进入了第1级,即用户模式级别。00分享举报为您推荐 cmd什么意思 怎么创建cmd快捷方式 cmd输入ipconfi...
You can visitCisco Hands On Course with Packet Tracer IP Configurations Beforeconfiguring SSH, firstly, we will configure IP addresses of router interface and the PC. We will use the below IP addresses: Router fa0/0 Interface IP : 10.0.0.1 Subnet : 255.255.255.0 PC IP : 10.0.0.2 Subnet :...
Switch(config)#hostnameSW-1[CHECK HOSTNAME ON INSTRUCTIONS]SW-1(config)#banner motd $This is Switch$SW-1(config)#line console 0SW-1(config-line)#password ciscoSW-1(config-line)#loginSW-1(config-line)#exitSW-1(config)#enable secret classSW-1(config)#service password-encryptionSW-1(conf...
But when I reconnect it as PC-->>Cisco 4331-->>Fios Router: I cannot get the internet into the computer. Do I have to set up forward and backward static or default routes. I noticed that I have a Gateway of last resort set on the router but a default router address set in the ...
Router1(config-subif)#standby 1 track gigabitEthernet 0/1Router2(config)#int gigabitEthernet 0/0.1Router2(config-subif)#standby 1 ip 170.10.0.100Router2(config-subif)#standby 1 priority 210Router2(config-subif)#standby 1 preempt Router2(config-subif)#exit %HSRP-6-STATECHANGE: GigabitEthernet0...
ref-->http://www.cisco.com/c/en/us/support/docs/switches/catalyst-2940-series-switches/109304-manage-vlandat.html a.2--> As soon as you boot a fresh/cleaned box AFAIK you enter the System Configuration Dialog to assist you to create&saveONnvram the initial startup-config for this devic...
cisco software switch config Go to solution muhammadShareef Level 1 05-02-2022 03:25 PM hello everybody! I am a student at the first year of SoftwareEng. and we are learning how to use the cisco packet tracer. our proff. asked us to connect 24 stations (20 pc 2 printers and ...
with the relevant initial configuration for each device. The lab also lists new requirements, after which you should create the additional configuration to meet those requirements. You can do the lab on paper, in a text editor, or use software tools like Cisco Packet Tracer or Cisco Modeling ...
CONFIG_IP_ADVANCED_ROUTER=y CONFIG_IP_FIB_TRIE_STATS=y CONFIG_IP_MULTIPLE_TABLES=y CONFIG_IP_ROUTE_MULTIPATH=y CONFIG_IP_ROUTE_VERBOSE=y CONFIG_IP_ROUTE_CLASSID=y # CONFIG_IP_PNP is not set CONFIG_NET_IPIP=m CONFIG_NET_IPGRE_DEMUX=m CONFIG_NET_IP_TUNNEL=m CONFIG_NET...