Example-1: In this example, the candidate configuration includes multiple PBR commands under a single route-maprmap1: route-map rmap1 permit 10 set ip next-hop 1.1.1.1 2.2.2.2 set ipv6 next-hop 3::3 set ip n...
CISCO(config)#vlan 10 CISCO(config-vlan)#name guanli 设置vlan名称 5. 设置vlan的ip地址以及网关 CISCO(config)#int vlan 10 CISCO(config-if)#ip address 192.168.0.1 255.255.255.0 6. 配置telnet远程登录 CISCO(config)#line vty 0 4 CISCO(config-line)#pass CISCO(config-line)#password 123456 CISCO(...
asked us to connect 24 stations (20 pc 2 printers and 2 servers) to a 2950-24 switch, and repeat that four times and then connect the four switches to each other in a star topology. 0- Is that even possible ? or he made a mistake when he wrote the exercise ? 1-how am I su...
4000 Series Switch industriais dos Ethernet de Cisco - Algumas relações abaixo podem abrir uma janela de navegador nova para indicar o original que você selecionou.
cisco 路由器&switch权限管理:使用privilege exec level 14 show running-config后,看不到啥内容 当我们想在cisco 路由器或交换机上执行权限分级管理时,常常需要为不同级别的用户分配超出默认设置的命令,比如show run就是最基本的排错命令。 但是当你的用户级别处在0-14时,是无法执行该命令的。你可以使用如下命令...
在Cisco 3560三层交换机上配置命令Switch(config-if)# no switchport的作用是( )。(选择1项) A. 删除该端口上的配置 B. 将该端口配置为二层交换端口 C. 将该端口配置为三层路由端口 D. 将该端口配置为Trunk端口 相关知识点: 试题来源: 解析 C 、将该端口配置为三层路由端口 ...
cisco WS-C4506-E (MPC8572) processor (revision 6) with 2097152K/20480K bytes of memory.Processor board ID SPE174400AWMPC8572 CPU at 1.5GHz, Supervisor 7L-ELast reset from PowerUp1 Virtual Ethernet interface244 Gigabit Ethernet interfaces2 Ten Gigabit Ethernet interfaces511K bytes of non-volatil...
百度试题 结果1 题目在CISCO 3550三层交换机接口模式上配置switch(config-if)# no switchport 作用是( )。 (选择1项) A. 关闭些端口 B. 变成二层端口 C. 变成三层端口 D. 配置中继端口 相关知识点: 试题来源: 解析 c) 变成三层端口 反馈 收藏 ...
30006, General: AP-manager interface with backup port, incorrect configuration: %Interface name% Never configure a backup port for an AP-manager interface, even if it is allowed in older software versions. The redundancy is provided by the multiple AP-manager interfaces. REFERENCE: Wireless LAN ...
把交换机A的主机名改成Switch。配置进入特权模式的密码为cisco。在全局模式下使用指令的关键字hostnamenameenablepasswordpassword5、在交换机A上创建VLAN。在全局模式下使用指令的关键字vlanvlanid在vlanconfig模式下使用指令的关键字namename6、把接口分别划分到不同的VLAN中。在全局模式下使用指令的关键字interface...