该成果以“Micelle-Facilitated Gelation Kinetics and Viscoelasticity of Dynamic Hyaluronan Hydrogels for Bioprinting of Mimetic Constructs and Tissue Repair”为题,发表在中科院双一区TOP期刊Composites Part B上。宁波大学医学部张华博士(研究方向:创伤修复材料与生物打印)为论文第一作者,中山大学付俊教授、澳大利亚伍伦...
由于F127DA在水溶液中自组装为纳米胶束，能作为耗散能量的巨型交联点，因此在光引发聚合后能显著提升了动态水凝胶的力学刚度与稳定性。通过分子动力学模拟与引入抑制剂的实验，证明了F127DA自组装的纳米胶束与HAMA-ADH和OHA之间形成了氢键作用，从而提升了水凝胶的动态凝胶化动力学。快速凝胶化和双交联的稳定结构使该动...
近日,吉林省结构与功能材料科技创新中心团队在双一区期刊《Composites Part B》上,发表了最新研究成果“Electrospun green fluorescent-highly anisotropic conductive Janus-type nanoribbon hydrogel array film for multiple stimulus response ...
2023年9月,创伤医学中心王光林教授团队在Composites Part B: Engineering(IF:13.1)发表题为:From brain to bone: Harnessing extracellular vesicles released from TBI to enhance osteogenesis by 3D-Printed hydrogel scaffold的研究论文。该研究进一步验证了创伤性脑损伤(TBI)可加速肢体骨再生过程,并且发现了创伤性脑损...
近日,我院整形外科/烧伤科李正勇教授联合四川大学国家生物材料中心王云兵教授团队在Composites Part B: Engineering(IF:13.1)发表题为A composite hydrogel improves the survival and differentiation of human iPSC-derived neural stem cells after ischemic stroke的研究论文。研究构建了一种仿细胞外基质的动态适应性水凝...
COMPOSITES PART B-ENGINEERING影响因子(IF)11.322属于材料科学、复合材料SCIE(Q1)区、工程,多学科SCIE(Q1)区适宜工程技术、管理科学、综合性期刊学者发表,COMPOSITES PART B-ENGINEERING录用难度较易 来源Elsevier官网:51%,审稿周期,历年影响因子分析、投稿官网地址等信
which provides a physical meaning to the dynamic J-integral as the variation of the Hamiltonian of the system due to an infinitesimal translation of the inhomogeneity if linear momentum is conserved in the domain, is extended here to the dynamic M- and L- integrals in terms of the 'if' con...
IFSS between silane treated Jute fiber and PP matrix was higher than the untreated or even alkaline treated cases. From the dynamic contact angle results, micromechanical IFSS was not always consistent with thermodynamic work of adhesion, W a in the interface. Since hemicellulose and lignin could...
Composites Part B: Engineering Volume 29, Issue 2, 1998, Pages I–II High Temperature Composites and Interfaces: Analysis, Processing and CharacterizationKeywords for composites: parts a and bShow moreShow less Choose an option to locate/access this article: Check if you have access through your...
28(a) and (b). If the combination of mechanical cutting and mechanical polishing is used, the mechanical damage during the sample preparation have a great impact on the subsurface machining defects and some of which may not be observed. Diaz et al.54 observed subsurface defects during micro-...