The LCD module used in this project is JHD162A. This is a 16×2 LCD module with 5×8 character dots. The LCD module has a 16-pin interface. The LCD is interfaced with Arduino in a 4-bit mode. The pin 1 (GND) and 16 (LED) of the LCD module are connected to ground. Pin 2 ...
lcd.begin(16, 2); lcd.createChar(0,a); lcd.createChar(1,b); } void loop() { // put your main code here, to run repeatedly: lcd.setCursor(0,0); lcd.write(byte(0)); lcd.setCursor(1,0); lcd.write(byte(1)); } 其中lcd.createChar(0,a);用来创建自定义图形,第一个参数为序号(...
inty,intdat){LCD_SET_XY( x, y );LCD_Data_Write(dat);}/** LCD写字符串*/voidLCD_Write_String(intX,intY,char*s){LCD_SET_XY( X, Y );//设置地址while(*s)//写字符串{LCD_Data_Write(*s);s ++;}}voidsetup(void){inti =
I built an arduino Uno R2 temperature datalogger using the Adafruit data logging shield, 6 ds18b20 onewire sensors (using the DallasTemperature library) and an Adafruit RGB 16 x 2 color LCD. I got a lot of help from Adafruit_support_rick on getting everything working, thanks: other who mig...
你将学到如何使用16X2的LCD液晶显示屏 接线图 接线表格 arduino代码 /* LiquidCrystal Library – Hello World The circuit: * LCD RS pin to digital pin 12 * LCD Enable pin to digital pin 11 * LCD D4 pin to digital pin 5 * LCD D5 pin to digital pin 4 ...
这个例子程序打印"Hello World!"到LCD上,并显示Arduino复位之后的时间(秒)。 在一块 2×16 LCD 上程序的输出 液晶显示器有一个并行接口,即单片机同时操作若干接口引脚来控制显示。该接口包括以下引脚: 一个寄存器选择(RS)引脚:控制在液晶显示器的内存什么地方写入数据。您可以选择的数据寄存器(保存什么在屏幕上),...
±6.144V / (2∧16 – 1) = ±6.144V / 32767 = ±0.1875 mV 与Arduino UNO 内置的 10bits ADC,每步 4.85mV 相比,精度提高了 25倍。如果PGA 设为1x 增益,即测量范围降至 4.096V,精度为 ±0.125mV,如果 PGA 设为16x 增益,测量范围降至 ±0.256V,精度可达 ±0.0078125mV。简单来说,PGA 增益越大,...
Arduino or Genuino Board LCD 显示屏 (和日立HD44780驱动兼容) 焊接到LCD显示屏引脚的排针 10k ohm 电位计 220 ohm 电阻 连接线 面包板 电路 在连接液晶显示屏到你的Arduino板之前,我们建议到焊接一组排针到LCD显示屏的连接器上(14或者16引脚数),你在上面的图可以看到。
Arduino or Genuino Board LCD 显示屏 (和日立HD44780驱动兼容) 焊接到LCD显示屏引脚的排针 10k ohm 电位计 220 ohm 电阻 连接线 面包板 电路 在连接液晶显示屏到你的Arduino板之前,我们建议到焊接一组排针到LCD显示屏的连接器上(14或者16引脚数),你在上面的图可以看到。
Arduino or Genuino Board LCD 显示屏 (和日立HD44780驱动兼容) 焊接到LCD显示屏引脚的排针 10k ohm 电位计 220 ohm 电阻 连接线 面包板 电路 在连接液晶显示屏到你的Arduino板之前,我们建议到焊接一组排针到LCD显示屏的连接器上(14或者16引脚数),你在上面的图可以看到。