登录主要或辅助上的CMX HA Web界面(https://server_ip:4242)。如果服务器正在主动同步,“监控”(Monitor)页面上有一个标记为“故障切换”(Failover)的按钮。在最右侧的enable auto-refresh上。 手动故障切换CLI(仅供参考): 第五步:故障恢复 要在辅助设备上运行CMX,必须将其视为临时情况,直到确定主要故障的根本...
例如,对将连接到主WLC的物理端口使用port-channel 1,对将连接到备WLC的物理端口使用端口port-channel 2。 Configure Port-channel to Primary WLC (WLC01): interface range Te1/1/1-4description Trunk Primary WLC01 channel-group1mode activenoshutdowninterface Portchannel1description Trunk Primary WLC01 Port...
4.2. The WLC is in High Availability (HA); Assurance does not work after failover. This can occur if the HA is not formed by the Catalyst Center. In that case: remove the WLC from Inventory, break the HA, discover both WLCs, and let Catalyst Ce...
I've 2 Physical WLC 9800 in SSO, and I'd like to know if it's possible to monitor the Management AP Interface to force a Failover if it's not reachable. I physically shutted the Interface that carry the AP Management IP to see what's happening, and all my APs were losing connecti...
You know from the AP you have setup up to three WLC in its "High Availablitity" settings. It is very important, actually I can fource our AP to failover to the HA WLC without shutdown our production WLC, that helps me a lot to do the maintain jobs on our production WLC. Hope tha...
Failover等级 全局HA配置 连接AP到控制器 *2100系列和WLCM没有service port 目前版本支持同时支持多国家 在AP和控制器不在同一网段的情况下,建立AP能够获取IP Address 的地址池,加上Option 43 WLC-router(config)#ip dhcp pool LWAPP-AP WLC-router(dhcp-config)#network WLC-router(dhcp-config)#default-router...
30009, General: Spanning Tree Protocol is enabled in controller, this must be disable, as this may cause stability issues STP should never be enabled on controller, as it has severe effects over network stability. REFERENCE: Wireless LAN Controller (WLC) Configuration Best Practices ...
5.1版本对HA的增强 Failover等级 全局HA配置 第四十三页,共一百一十一页。 Presentation Title Size 30PT Option 2: Live 连接AP到控制器 第四十四页,共一百一十一页。 Controller里的Port还有Vlan以及Interface的对应关系 Controller必需配置的接口 带内管理接口—“Management Interface” LWAPP Tunnel 终结接口—“...
配置基础思科中小企业统一通讯方案部署和功能演示AP发射功率调节(AP1131)TxPowerAP125.1版本对HA的增强Failover等级全局HA配置仰盈琉纤扦宵刊惯竣蔓配垫掷场富罚柬扇萧继转格侧辣垄来捍谦委帆伍菇CISCO无线控制器配置基础思科中小企业统一通讯方案部署和功能演示5.1版本对HA的增强Failover等级全局HA配置仰盈琉...
Using EEM on the 3850 core I was able to detect if the default route learned VIA OSPF was removed from the routing table – if that happened, then run the command “No shut” on my MPLS uplink and EIGRP would take over. If the default route was learned at some point through OSPF wh...