正在建立具有deny_oid角色的SNMPv3使用者: switch# config t Enter configuration commands, one per line. End with CNTL/Z. switch(config)# snmp-server user snmpv3user deny_oid auth sha password!123 priv ? WORD Privacy password for user (Max Size 134) switch(config)# snmp...
PI使用SNMP來管理無線控制器、存取點和客戶端裝置。Cisco 2500系列無線控制器裝置需要正確配置SNMP。 請完成以下步驟: 使用URL登入PI Web介面: https://<prime-ip-address> SNMPv2是在Cisco 2500系列無線控制器上配置的。要透過控制器Web介面配置SNMPv2,請導航到管理>SNMP> Communities。Cisco 2500系列無線控制器的預...
Switch Virtual Interface (SVI) Configuration Example and Explanation 2. Port 以太网端口有三种链路类型:access、trunk、hybird Access类型端口:只能属于1个VLAN,一般用于连接计算机端口; Trunk类型端口:可以允许多个VLAN通过,可以接收和发送多个VLAN 报文,一般用于交换机与交换机的连接。 Hybrid类型端口:可以允许多个VLAN...
要配置SNMP,我建议首先查看一下设备的信息。比如下面这些: Router(config)# snmp-server contact David Davis - Network Admin - 555-1212 Router(config)# snmp-server location Dallas, Texas, USA Router(config)# snmp-server chassis-id Cisco2610-Router 接下来我们要配置SNMP以便NMS可以监视它。配置SNMP的方...
Switch(config)#snmp-server host *.*.*.* version 2c public # SNMP采用版本2,public作为团体名称 Switch(config)#snmp-server host *.*.*.* traps public# 指定SNMP Trap的接收者为192.68.98.166,发送Trap时采用public作为团体名称 Switch(config)#snmp-server trap-source vlan 1 #设置vlan1虚接口IP地址做...
1. switch配置命令 (1)模式转换命令 用户模式---特权模式,使用命令"enable" 特权模式---全局配置模式,使用命令"config t" 全局配置模式---接口模式,使用命令"interface+接口类型+接口号" 全局配置模式---线控模式,使用命令"line+接口类型+接口号" 注: 用户...
Current configuration : 123 bytes ! interface GigabitEthernet1/0/1 switchport trunk encapsulation dot1q switchport mode trunk spanning-tree portfast end Switch# 在Cisco 2500系列无线控制器的管理接口配置是直接的并且有启用的动态AP管理。 配置了两个 WLAN。WLAN1和WLAN2被映射对管理接口并且服务客户端。
switch(config)#vtp mode server;设置发vtp模式 switch(config)#vtp mode client;设置发vtp模式 交换机设置IP地址: switch(config)#interface vlan 1;进入vlan 1 switch(config-if)#ip address;设置IP地址 switch(config)#ip default-gateway;设置默认网关 ...
通过Ethernet上的SNMP网管工作站。 但路由器的第一次设置必须通过第一种方式进行,此时终端的硬件设置如下: 波特率:9600 数据位:8 停止位:1 奇偶校验: 无 二、命令状态 1. router> 路由器处于用户命令状态,这时用户可以看路由器的连接状态,访问其它网络和主机,但不能看到和更改路由器的设置内容。
Configure read-only SNMP community string (yes/no) [n]: //配置只读SNMP共同体字符串 Configure read-write SNMP community string (yes/no) [n]: //配置读写SNMP共同体字符串 Enter the switch name : MDS9148-1 //配置交换机名称 Continue with Out-of-band (mgmt0) management configuration? (yes/...